MGR6772BDB Maytag Range - Instructions

Did the diagnostic tests from the literature provided in a bag on the back of my stove I had no idea it was on the back of my stove because I had this stove installed when it was brand new
The final test indicated the igniter was bad and this is a common cause due to age wear and tear and just use of the oven
So I ordered one. It came extremely fast
It was a an OEM part
I had the oven back in operation in 15 minutes that includes R&R of the stove back and oven racks and inside fire tube covers and fire tube
I then replaced the bad igniter with the new one on the fire tube then reinstalled the fire tube
Then I did the Prefire test with the Gas turned off and the igniter lit beautifully
Then the final test was I turned on the gas and did the Prefire test again AND the fire tube lit up and beautiful blue flames came out the fire tubes tiny holes
Then I finished putting the back and inboard fire tube covers back on
Then I put the racks back in
This is what I did from start to finish and the Most important thing was I made my wife extremely happy

Replaced Igniter, only problem was the connector was in the back of the unit. I had to take off the back of the unit. About 12 small hex screws to make connection. Other than that it was pretty easy.

You Tube!!! Didn’t find my exact oven, but watching a couple of videos was extremely helpful. Replacing the igniter was basically simple, but since it was a first for me, I took my time. Probably saved $200. The part was just over $100.

Removed door from oven by pulling up at the first stop point after opening the door. Removed the outer shell by removing 5 screws. Disassembled the inner door by removing 6 screws. Be careful with the insulation blanket (fits in a molded portion of the inner door). Glass windows can be removed (for cleaning) via a couple screws. Old gasket/seal is held in-place via spring-clips; just squeezed each clip, pushed each thru their respective holes, and pulled off the worn-out gasket. New gasket snapped in-place by pushing the clips thru the respective holes. Reverse the process to reassemble the door. You can do this job in 15-20 minutes. Took us longer because it took some elbow-grease (and patience) to clean the crud off the glass windows.

Waited for my husband to do it, but when he didn't, I tried it. Very simple! Just pulled the old gasket out of the pinch pin holes in the door, then replaced it. Tuck the one end into the hole at the bottom of the door, then match up the little pinch pins on the gasket with the holes in the door - matches up perfectly! Be sure to tuck in each of pinch pins till they sort of "snap" into each hole. Took me 5 minutes, tops. Works great now, no more lost heat around the edge of the door.

Removed the approximatly 10 screws that hold on both the upper and lower pieces of sheet metal that cover the back of the oven. Removed the screw holding in the temp sensor. Unplugged and removed the old sensor. Plugged in and installed the new sensor (using one of the included adapter wires supplied with the sensor). Put the 2 pieces of sheet metal back on and plugged in the oven.

Took the old levelling leg out and screw the new one in.

Simply remove two screws take old one off and line up and put new one on and replace the two screws. Couldn't have been easier.

Change Temp Sensor-Turn off the power or unplug unit, remove oven racks, removed the two screws that hold temp sensor, pull out and unplug.
Change Igniter-Remove two front screws holding bottom cover on and lift out of place, next remove the two wing nuts holding square plate on, next remove the three screws holding gas tube in place, remove gas tube pulling wire carefully through and unplug it. Remove the two screws that hold igniter to gas tube. I found it easier to pull stove out and remove back bottom left square cover held in with four screws to fish the igniter cable back through.
Oven now heats to 350 in 8 minutes.

Remove the door, remove screws from all sides

Remove sides and face of oven door by sliding down from under the oven handle trim.

Remove screws on 2nd light of glass and set aside.

Now you are at the inner door panes. their should be two in an insulated type unit.

Remove the remaining screws from the handle pracket and the permiter frame for the glass/insulation. Remove permiter frame and set aside.

Pull out inner door glass frame. get a pair of pliers and bend tab on frame up so you can pull the frame sightly apart, replace the glass, secure frame tightly around glass slide tab back into reciever slot and bend down ( you may need another person to assist in keeping both lights in the frame while trying to ben tab back in to place)

reassemble door as it came apart carefull not to over tighten the screws, they strip easy.

Just removed the shield (2 wing nuts) than the burner (1 Screw). THe back needs to be removed to unplug the igniter. I than reversed the process until I got to the plug and found that I had 2 male ends. I than had to remove everything and go back to square one until I find the part with the correct end (which should be Female) I'd check this before getting too deep into the repair.

Turned off the gas line & unplugged the oven. Pulled oven away from the wall to access the back of the oven. Removed the back panel (screws) on the oven & the few inner oven parts covering the broken igniter. Sprayed WD 40 on the threads of screws holding the old igniter in place. Removed old igniter screws with a nutdriver & unplugged it from the back of the oven. Installed the PartSelect replacement igniter & plugged it into the wiring receptacle. Reassembled the parts covering the new igniter & screwed the back panel back onto the oven. Plugged oven in, turned the gas back on & pushed the oven back into place. Tested the new igniter. Woohoo, oven works again & wife if happy!

Put a new one in.

From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.

Easy instal most of time was taking off and replacing back panel Found watching how to videos helpful