MGR6772BDQ Maytag Range - Instructions

Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.

First I removed the lower tray and all parts covering the ignitor on the upper oven. 2. Then I removed the screws holding down the ignitor and flame distributor. 3. I then had to pull out the oven from the wall and remove the back panel to expose the wires connecting the ignitor. This required the removal of about six screws but they were fairly easy to get to. 4. I disconnected the ignitor from the back panel then went around to the front of the oven and pulled out the ignitor and all of the attached parts. 5. Here's the tricky part. The screws holding the ignitor in place had fused from the heat and then the threads stripped when I tried to remove them. I had to use a dremel tool and cutting wheel to carefully cut the screws off and then went to buy some replacement screws from the hardware store. 6. I replaced them with a nut and a bolt, to hopefully avoid the same problem for later replacement if necessary. 7. I then replaced everything the same way it came out and all is working like new!

First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will cause the plastic plug connector to melt from oven heat.

First removed the old gasket using a needle-nose pliers. Then placed new gasket by inserting the little clips on the gasket. Took 5 minutes. Great instructions from Repair Forum.

This is fairly easy for anyone to do. First I opened up the front (silver part) of the oven door by removing the screws at the top and the bottom. Then I kept on removing the various layers of glass... the 2 outside ones are removed by removing their respective screws and then you get to the inner-most. These 2 inner ones are in a frame that holds them together. I removed the large silver frame that holds the insulation and the 2-glass-frame in it. Just remove the screws and then tilt the insulation frame out a bit to remove the glass frame. You can tilt the entire insulation holder out but the insulation is soft and it starts to fall off. Just tilting it enough worked for me. Then I opened up the glass frame from one end, removed the left-over broken piece of the old glass pane and installed the new one in. Then reassemble. The entire process is very easy - but you will need another person for a few minutes when you remove /reinstall the glass frame inside the insulation holder. You would just need a little help holding everything... nothing technical. I would rate the repair technicality at 4 or 5/10. It could even be a 3 if there were less steps involved. Good luck! By the way, Amana/Maytag wanted $70 or so for the glass and then the repair fee. I got the part here for about $50.

Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

remove small panel on right side of stove,then un clip moduke and put wires from old module to new one.
Exact fit nomproblems.

Open top oven door and remove the 2 front screws which hold the burners and controls to the frame. DO NOT lift the burners more than an inch or so to look inside. You WILL bend the gas lines in the back if you do. Pull out stove from the wall, shut off gas supply and disconnect hose if needed to have room to work. Remove top back panel and remove the 3 wires connecting the top burner assembly and also remove the 2 gas lines. Now you will be able to remove the burner assembly safely. Flip it over and try to unscrew the screw holding the igniter. When you fail, drill it out and get a small metal screw to replace it. The metal is soft and the screw is hard, so drill carefully. The rest is easy, put in the new igniter and screw. and put it back together.

First I removed the two philips screws inside the oven that hold the element in place. Then I pulled the sensor out and the two insulated wires through the hole to reveal the plastic connector. I unsnapped it from the connector and replaced it with the new element. Then, behind the oven, I removed five or six philips screws on the right side of the large panel so I could pull the wires back through the layer of fiberglass insulation to make sure only the sensor itself would be exposed to the oven's heat. I then secured the back panel again and replaced the two philips screws holding the sensor in place.

Lifted door off hinges; removed lower oven spill plate; unmounted bake igniter from heat shield; pulled stove away from wall; removed rear access panels (4 screws); unplugged bake igniter; installed new part; vacuumed behind stove and mopped floor (this took more time than installing the part); oven is back in cookie baking mode!

Having no manual nor finding any instructions online, I spent a while trying to figure out how to safely get to the ignitor mounting screw under the range top. I popped the snap clips on either side of the stove to loosen the top and pulled the top up a few inches to see why it was being difficult to raise. It turns out that the gas piping was solidly attached from the controls to the burners and I was slightly bending the tubes as the top was raised. The tubes have angles and curves to "accept" the bending pressure I was applying, so it looked like I was doing the right thing. In case I was not doing the right thing, however, I raised the top only enough to get access to the ignitor base and mounting screw. Then the fun began as the screw would not loosen. After several attempts using liquid wrench, tapping on it, etc., the screw head finally just broke off. Uh-ohhhh. Not to worry, however, as there was an empty mounting hole right next to the old one that appeared to be able to work. The mounting screw for the new ignitor was backordered, so I tried a couple dozen different screws I had in my toolkit and finally found one that would fit width-wise, but I had to nip off some of the length to get it to seat properly. The replacement ignitor also had a different width blade connector than the original so I had to grind away some of its width to reattach it to the lead wire. If I had a different sized blade receiver, I would have instead replaced the receiver on the end of the lead wire. It took about 90 minutes in all.

removed oven door, removed screws from bottom and sided, door is in layers, removed door layers like taking apart a sanwhich layer by layer, once i got to the inner layer i just had to bend out the little tab on the frame,remove the broken pane and place in the new one, bend the tab back and then put the door back together layer by layer, it was very easy and saved me money, and frustration in dealing with a repair man from a well known company who tried to tell me I needed to replace the whole door as the glass was factory sealed in the door, WELL! this girl's hair may be blonde but not that blonde, I received the glass the very next day, and it took me 40 minutes tops to replace the glass, EASY! KC

I ordered the door glass from Part Select, which arrived quickly and in good condition. I loosened two sets of screws under the bottom glass holder frame, removed three screws at the top of the door to give more room. Slid the glass in place, re-installed and tightened the screws.The stove door looks great and works great. Great customer service too.

Pulled oven out of the cabinet/wall and pulled sensor out and replaced with new one.

A few years previously I had this same problem and a PROFESSIONAL had replaced the sensor.
Thus this time I knew what the failure was and obtained the sensor from Part Select. Having observed the PROFESSIONAL replace the sensor before; I followed his easy technec only to learn that when the sensor was pulled from the aft wall of the oven that the wires had deteriorated and the plastic plug melted. Therefore it was neccessary to remove the oven from the wall cabinet. Then I removed the panel from the back outside of the oven, cut back the wires and because the kit from Part Select contained additional connectors was able to splice in a replacement connector. Installed the new sensor and reinstalled the oven. LESSON LEARNED; when the PROFESSIONAL had replaced the sensor he had failed to feed the wiring and plug back past the insulated chamber, directly behind the oven, into the cool area assessable by the panel on the aft side of the oven thus the plug and wires were exposed to the heat of the oven. What would commonly be a few minutes job turned into an afternoon project.