ACR4303MFS4 Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dan from Caddo Mills, TX
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inside Light would not work
Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from sanborn, NY
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the drip bowls had rusted through
a really simple fix! the parts came really quickly and all i had to do was pull the heating elements out along with the old drip pans and line up the new pans and push back in. the drip pans weren't 100% perfect as they were a universal fit, and were missing the clips that help the heating elements i nplace, but they look fine and do the job all the same.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gudrun from Santa Fe, NM
- Parts Used:
- W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacement of drip bowll
take the old one out, but the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irina from Green Cove Springs, FL
- Parts Used:
- W10196406RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ugly looking drip bowl.
Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Negaunee, MI
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.
Took off the screws on the back of the stove and took out the sensor, and put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from windsor, VA
- Parts Used:
- WP3148952
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
water pump went out
it was very easy i took the pump off only two clips and two hoses holding it type in the model number at parts select it came right up soi new it right one from the picture got with in 3 days put it back on less then 10 mins
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from SALCHA, AK
- Parts Used:
- WP3149400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Burner control failure/unable to regulate temp.
Unplug range from 220VAC outlet. Remove screws on back of range control panel and lift cover exposing controllers and wiring. Remove burner controller mount screws. Measure old controller shaft length/new controller shaft length (per instructions). Adjust new burner controller shaft length. Remove wiring from old controller (one at a time) and place on new controller. Install new controller and secure with 2ea mount screws. Re-assemble cover/control panel. Plug range into 220VAC outlet. Have wife ops check....everyone's happy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph R. from Candia, NH
- Parts Used:
- WP3148952
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Not heating properly.
Removed rear panel and removed switch. I placed wires from old switch to the new one. re installed switch an back panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Vero Beach, FL
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip plans needed replacement
Removed old ones replaced with new oned
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Emmett, ID
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No Problem
Needed new drip pans for range top. Easy fix. Was impressed on how quick the parts were shipped out to me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Kings Park, NY
- Parts Used:
- W10196406RW, W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace drip bowls
I took the old bowls out and dropped the new bowls in. No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Wooster, OH
- Parts Used:
- WPW10181986
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove kept turning off
Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kyle from Schwenksville, PA
- Parts Used:
- W10196405RW
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted drip bowl
remove burner by hand and remove old drip bowl replace with new bowl inspect burner for ware and insert back into slot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Vanderbilt, PA
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
I had a power serge and it burned the Plug at the termial block and melted a few wire.
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Clinton, TN
- Parts Used:
- WP3149400
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner goes full hot at any setting
First, I turned off the power at the switch box. Moved the stove out (That was a problem, because I am 80 years young) Removed the back panel, and moved the wires one at a time to the new switch. Removed the selector, then removed the 2 screws holding the switch in. Installed the new switch installed the dial selector, turned the power back on, and checked the burner. It works as advertised!!!!! Moved the stove back to its original position, and got a hug from my wife. PHEW!!! Now I think I'll take a nap.
Was this instruction helpful to you?
Thank you for voting!