24JN-7V8 Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Roger from Greenwood, AR
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven would not light, but igniter would glow.
Removed Old Igniter and installed new one, parts and connector fit fine, no modifications needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Hanover Park, IL
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven burner would night ignite
Replaced the ceramic glow ignitor by removeing the two screws holding it to the mounting bracket. Gas and electric were tturned off. Unplugged the ignitor from rear of oven. Installed new switch in the same way and if worked perfect. Part was ordered online for $48. I saved one hundred dollars by doing it myself. My outdoor grill was harder than this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Belleville, IL
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Things cooked in the oven were taking longer than usual to be done.
Using a remote digital thermometer, noted that the oven temp reached operating temp, then fell 40-50 degrees, was slow to recover. After reading entries from others on your web site, removed oven floor and watched the burner operation. The igniter would light the gas at first, the temp would go up, gas would shut off. Then when the igniter came on again, it would glow for a long time before gas would come on.The replacement was very simple, even though one of the mounting screws twisted off, the remaining screw seems to be holding.Was a simple unplug old connector, insert new connector. The optional parts included in the kit were not needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joan from florissant, MO
- Parts Used:
- 12400035
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not light
My brother-in-law did the repair as I am a scardy-cat and didn't want to tackle it myself. The most difficult part of the repair was the awkward position you have to get your body in to do the repair. Other than that it was a piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jon from Mayville, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
ignitor would heat enough to open gas vavle to lite oven
unplugged the oven, unplugged the ignitor and removed the two screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carole from Girdwood, AK
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
very slow heating, smell of gas
Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HELMUT from MIDDLE VILLAGE, NY
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven would not light even though the glow plug lit.
Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.
The oven worked like a charm again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neville from Lithonia, GA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Would not Light
Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Dearborn, MI
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not heat to temp and could smell gas.
Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- scott from newtown, CT
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven wouldn't get hot
well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation around wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Canton, OH
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not heat, ignightor glowing, no gas. (Current not flowing from igniter to valve)
1. Pulled the bottom plate out of of the oven (plate separating oven and broiler). 2.Remove the gas tube. 3.Remove back plate found at the bottom of the inside of the oven (4 screws). 4. Remove igniter from bracket and disconnect wires. 5. Connect wires from new igniter to oven (2 wires). 6. Connect new ignighter back to bracket and 7. re-assemble steps 3,2,1. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roberta from Los Angeles, CA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven wouldn't light.
I removed the oven door and floor, removed the two screws holding the old part in place, unplugged it from the wiring harness and plugged in the new part and replaced the screws. Fixed in 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LINDA from SALEM, OR
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Would not heat. Broiler was fine, just no oven.
Well, this wasn't my first rodeo, this is the second ignitor I have replaced in my oven, first being the broiler. It is very simple, unscrew the old one, screw in the new one. The hardest part was cleaning up the mess I found UNDER THE OVEN!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kenneth from breaux bridge, LA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven would not light
open oven door remove bottom tray pull off two screws unplug wire remove old part install new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- graham from littleton, MA
- Parts Used:
- 12400035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
oven ignighter would glow, but oven would not work
I removed the two screws holding the ignighter on, pulled it a few inches, disconnected the plug, plugged the new ignighter in, tightened the two screws, turned on the power, and it worked. 1,2,3.
Was this instruction helpful to you?
Thank you for voting!