68EN-3CX Maytag Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Daniel from Prescott, MI
- Parts Used:
- 7201P036-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Burned up oven door gasket needed replaced.
I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt away about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marjorie from Swanton, MD
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner would not stay heated had to wiggle the burner to make heat
Replaced with the new burner works like new. Thanks a bunch!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from killingworth, CT
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners weren't heating
Unplugged old burner elements. Popped in new burners. Turned on the burners to test.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from Austin, TX
- Parts Used:
- WP660533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Electric Stove Burner was working unreliably
pulled out the old burner, plugged in the new burner. Turned on the power and it heated up very quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lisa from PORT JEFF STA, NY
- Parts Used:
- WP660533
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The larger burners would stop working while in use.
The removal of the old burner and installation of the new burners was easy. Just lift the opposite side that rests on the rim and pull burner out. New burner then gets inserted and the opposite side goes right into rim. It took all of 30 seconds to replace both burners. I wish I had replaced these when they first started to go!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rolland from New Port Richey, FL
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The Broiler element split after oven self-cleaning
We at first thought the replacement could be done by just removing 2 screws.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the price of the element plus the cost for the service call.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the price of the element plus the cost for the service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Reston, VA
- Parts Used:
- WPY04000048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Replaced Broiler Element
Turned off oven power.Removed oven heat shield, element support clips and element mounting plate screws. Disconnected three element power wires and ground wire. Removed old element. Reversed removal procedure for new element install. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Thornton, TX
- Parts Used:
- WPY04000048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element burned out, broke circle, heat only half
Repair went fine, insert helped, just take your time and remember the way you took out. Started without takeing door off, I am to short and door comes off easy, unscrew the two screws holding element leaving one not quite off then the back two screws then go back to upper screw remove and element will pull out, remove 3 wires remembering the order, Wiring is a little tricky (in the stove-just 3 plugins), just pay attention and will go smooth. Then remove element and go backwards and presto your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra Collignon from SANTA CLAUS, IN
- Parts Used:
- WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Drip Pans were stained and burned on.
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Elba, AL
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burnt out
All went well except for error on instruction sheet.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.
Ground wire used on earlier Models attached to the ground lug is no longer used?? and should be removed!!! Guess what the ground wire has to be used or the element will not heat up.Soooo someone at the mfg. has no ideal what they are talking about,You have to ground the element or it will not come on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from SPRINGFIELD, OH
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler element was only working on one side
Grandson spent 1/2 hour installing unit and 15 minutes of that time was trying to get the very short grounded screw to begin to thread. It was a very small space to work in and it kept falling out. The instructions were a lot to be desired - almost nothing. He went to YouTube and got very explicit instructions. Then he had no problem as to what to do. The unit is working great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from SEATTLE, WA
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Half of broiler element worked
Turned off power at panel. Removed 2 Phillips screws holding broiler element support in place. Squirted 2 additional Phillips head screws attaching element to back of stove with WD-40 and removed screws. Slid element out to access electrical connection and used short phillips screwdriver to remove. Reattached electrical connection to new element with short screwdriver (no fun as you are cantilevered into the oven and have to hold the element, the screw and the screwdriver to do this). Slid element into support and screwed support to top of stove cavity to align element. Installed screws holding element onto back wall. Turned on power and ran element long enough to dissipate WD-40 fumes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from CHARLESTOWN, IN
- Parts Used:
- WP660533
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Element did not heat
Pulled out element, plugged in new element. About 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicki from ELSIE, NE
- Parts Used:
- WPW10196405
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Drip pans were old and with burnt on food that I couldn't get off. Disgusting!!
No problem Took off old ones and replaced with new.
Was this instruction helpful to you?
Thank you for voting!