CER1360BAW Magic Chef Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Russell from Coppell, TX
- Parts Used:
- WP74010750
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Bake Element shorted out, burned out hi-limit switch
-Disconnected power from oven at the circuit breaker.
-Removed oven door and racks.
-Removed two screws holding element to the rear wall.
-Carefully pulled element away from rear wall, exposing wire leads.
-Carefully detached wire leads with male Sta-Kon connectors from element ends. (Taking care not to break or weaken the wires at the connector.)
-Disposed of old element and placed new element in same position.
-Re-attached leads by very carefully sliding male Sta-Kon connectors into the new element connectors, taking care not to push too hard and bend element wire.
-Gently re-inserted element ends into wall and re-attached element to wall with original screws.
-Reconnected power and tested new element. Element did not heat.
-Disconnected power and looked for collateral damage from original element failure.
-Removed oven from wall, removed rear panel and identified the high-temperature limit switch.
-Removed Sta-Kon leads and checked switch for electrical continuity. It had none, apparently the result of the high current from original element short.
-Obtained new hi-limit switch from Part Select
-Removed and replaced hi-limit switch, re-attached leads.
-Replaced rear panel and reinserted oven in wall.
-Reconnected power and tested new element. Element heated normally.
-Returned racks to oven, re-attached door and done.
-Removed oven door and racks.
-Removed two screws holding element to the rear wall.
-Carefully pulled element away from rear wall, exposing wire leads.
-Carefully detached wire leads with male Sta-Kon connectors from element ends. (Taking care not to break or weaken the wires at the connector.)
-Disposed of old element and placed new element in same position.
-Re-attached leads by very carefully sliding male Sta-Kon connectors into the new element connectors, taking care not to push too hard and bend element wire.
-Gently re-inserted element ends into wall and re-attached element to wall with original screws.
-Reconnected power and tested new element. Element did not heat.
-Disconnected power and looked for collateral damage from original element failure.
-Removed oven from wall, removed rear panel and identified the high-temperature limit switch.
-Removed Sta-Kon leads and checked switch for electrical continuity. It had none, apparently the result of the high current from original element short.
-Obtained new hi-limit switch from Part Select
-Removed and replaced hi-limit switch, re-attached leads.
-Replaced rear panel and reinserted oven in wall.
-Reconnected power and tested new element. Element heated normally.
-Returned racks to oven, re-attached door and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sabrina from FREMONT, CA
- Parts Used:
- WPW10196406, WPW10196405
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Used part
Lift burners out of plug discard old drip pans replace new drip pans into plugs and done .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- barbara from greenville, SC
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
i had to replace my oven element as is cracked in half
after finding my part and thank god for you guys i recieved it early it only took 4 days to get here i unscrewed my old oven part and popped the new one in easier than making cookies and now i can bake til my hearts content thanks for being there for me
barbara krebs
barbara krebs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Hurst, TX
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element went out
First I turned the power off to the oven using the breaker switch. Removed the old bake element by first unscrewing the 2 screws for each bracket holding each side of the old bake element and unplugging the two current connections.
Replugged and rescrewed above. Turned breaker on for oven. Tested by turning oven to back and watching new bake element heat up.
Replugged and rescrewed above. Turned breaker on for oven. Tested by turning oven to back and watching new bake element heat up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhoda P. from Secaucus, NJ
- Parts Used:
- WP3413F018-19, WP3401F075-19
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I needed a broiler pan
I took the broiler pan out of the shipping container and put it in the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PETER from ROSEVILLE, CA
- Parts Used:
- WPW10345410
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner Failed
Unplugged old burner,plugged in new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Steelville, MO
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the lower baking element of the oven did a 4th of July sparkler show coming right out of the oven door three days before Thanksgiving
I had the part overnighted since Thanksgiving was in two days and we needed to be able to use the oven. I saw a video on the website that instructed how to unplug the stove. Unscrew the baking element from the inside of back wall of oven. Gently pull out the part to where it is attached to wires. Simply pull apart the male part from female parts. Replace the old element with new element and attach it to the pulled out wires. Then gently push back wires inside the back wall of oven. Screw the attachment back in. We then plugged the oven back in. Turned on the oven to about 300 degrees. We put an oven temperature gauge inside and after a time the oven temperature was at 300 degrees and steady. It was fixed. Thanksgiving was on!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thea from Greeley, CO
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
replacing broken bottom baking element
the hardest part of this repair was the wait for the element to arrive in the mail - which was in 4 business days - then took 5 to 10 minutes to get to circuit breaker box in garage. That was the longest part of the repair. My husband took the door off the oven after turning the circuit off in the garage. Followed directions from others who made the same repair and it was done in 2 minutes! Super easy - thanks for saving us money during this time of tight budgeting around the holidays! You're a lifesaver!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paola from High Bridge, NJ
- Parts Used:
- WP12001560
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just plugged the burner in and it was good to go.
The burner wouldn't work. I just plugged in the new one and all was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heidi from Lakeland, FL
- Parts Used:
- WP74010750
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Element was broken(literally).
First, turn off the breaker to the range. Then just remove the 2 screws that hold the element at the back of the oven. Pull the wire connectors apart or push them off with a regular screwdriver. Instructions that I read said to make sure the wires don't fall back through the holes, but in our case the insulation held them in place. Reconnect the wire connectors to the new element and reattach with the screws. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marion J. from Palmetto, FL
- Parts Used:
- W10196406RW, WPW10196405
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replacing old drip bowls
It was so simple & the parts fit perfectly. I appreciated all the help from your sales lady. Thanks again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lowell from Hardin, KY
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Couldn't find correct drip bowls that fit.
Removed old drip bowls, removed burners installed new drip bowls,installed burners. They fit perfect and I received them two days after ordering.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kathryn from piqua, OH
- Parts Used:
- WPW10196405, WPW10196406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old drip bowls were rusting, no chrome left
Took the old ones out and put in the new ones! What I am so pleased about it that I just went online and at Parts Select website it was easy to find what I needed, a fair price and the 4 bowls arrived within 2 days!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from BROWNVILLE, NY
- Parts Used:
- W11665456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
My original back leg broke because the floor is uneven. Had to pull it out several times.
Put the back of stove on blocks of wood to get high enough to screw the new leg in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from TROY, MI
- Parts Used:
- WPW10310249
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
The broiler broke at the ends.
My daughter repaired it without any problems.
Was this instruction helpful to you?
Thank you for voting!