31203PAQ Magic Chef Range - Instructions

took out burner and remove ignite r and reinstall a new one simple as that

Turn off power then turn to take old burner out ,
disconect 2 wire , .
Connect electric wire with new burner press in then turn and clock . Turn power on then start stove
and check .

The oven was inconsistanty lighting and I could not predict when it would. After reading some repair reviews I determined that the problem was most likely the igniter. I purchased one from your site and it arrived the next day. Awsome! Had to take out six screws to get to the wiring and removed the igniter. The wiring was a simple plug. Replaced the igniter in about 20 minutes and the oven has been working flawless every since. THANKS!

First I removed the bottom plate in the oven. The ignitor was located at the rear of the burner and I removed to screws and it was loose except for the two wires. Next I removed the bottom tray from the stove. Two screws held the metal guard in place at the rear of the stove. After removing the plate, I determined which wires belonged to the ignitor, unplugged them at the coupling and pulled the wires out through the bottom of the oven. Replacing the ignitor was simply to reverse the proceedure. PartSelect got the part right out to me, installing the new part was a breeze, and my wife calls me her "hero." This site was a real help and saved me a service/repair bill. Thanks!
Fred

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

Nothing to it - remove oven bottom, and burner cover, unscrew the 2 scews holding the igniter
(one of mine sheared off now only one is holding the new igniter in - it still works) unplug wire at the connector then reverse and the oven is as good as new. The best part is that I received my part in only 2 days.

I shut the gas off and removed the oven door pulled the oven out and removed the electrical access panel.
unpluged the igniter and removed the 2 screws holding the igniter and relpaced repluged.
right to self clean mode. Easy job no worrys
Be safe check your gas connection!!

Remove oven door, pan drawer, oven racks, bottom pan, flame spreader. Remove valve cover at back of pan drawer. Unplug old igniter. Remove two mounting screws holding igniter to gas tube assembly. Install new igniter, plug it in, and reassemble. Easy as pie! Oven works better than it has for a looooong time! Heats up to 400 in 5 minutes. Wife is happy! :)

I removed the floor of the oven (one screw) and the heat dispersal shield (one wing nut). Then I detached the old igniter using a socket set. I had to remove the bottom drawer to unplug the ignitor and plug in the new one. Then I reassembled. Total piece of cake and I have no experience whatsoever.

I replace the igniter first that didn’t work so I had to order the wiring and then I replaced that there was a cover that I took off with a screwdriver took the wiring off and put the new wiring in it it was that easy.

I found the panel on the innernet, ordered it and when it arrived I removed the old one and replaced it with the new one.

Open oven door remove trays.. remove floor of oven...remove single screw holding heat shield... unscrew two srews holding ignitor and unclip plastic...done..reverse to install

find the part (image is really helpful), buy, and replace. Like I said, it's really easy.

First I tried oven ignitor. Did not cure the problem. Then ordered short sensor and it cured the problem. Pull range out & unplug unit.From inside unit remove two screws holding short sensor in &pull out from inside. Unhook sensor. Slide in new sensor& secure with two screws. Had to remove two screws on back of oven to plug in sensor to existing plug. Very simple job.

We ordered the replacement igniter and basically was very easy to replace. We ended up spending $50 for the part as opposed to spending $261.00 that Sears was going to charge.