ACO1560AS (ASBEAMA) LG Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lynwood from GONZALES, LA
- Parts Used:
- 5230W1A012B, 5230W1A011B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Change the Charcoal Filter and Microwave Grease Filter (Normal Maintenance)
Both were easy to replace. I followed the instructions in the users manual which came with the microwave. On the grease filter, I removed the 2 Phillips head screws which hold the grill plate in place. I had to open the microwave all the way to remove the grill plate. The grease filter was easy to remove and replace with a new one. I then put the grill back in and secured it with the 2 screws. Easy Peasy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Krzysztof from NEW BRITAIN, CT
- Parts Used:
- 5230W1A012B
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
Leek
Change gasket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from CARY, NC
- Parts Used:
- 6549W1S013H
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
microwave turn table not working
Removed the phillips screws from the base.
Using a # 10 secure driver, remove the motor. (I recommend obtaining a secure star driver set to be sure you have the right size)
Replace the spacer, which is a separate part from the motor.
Reinstall the spacer and motor.
Reinstall the bottom panel.
Enjoy!
Using a # 10 secure driver, remove the motor. (I recommend obtaining a secure star driver set to be sure you have the right size)
Replace the spacer, which is a separate part from the motor.
Reinstall the spacer and motor.
Reinstall the bottom panel.
Enjoy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Cedar Park, TX
- Parts Used:
- 3B73362F
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Microwave failed to head and light, fan, and turntable failed to come on.
Problem was due to a faulty door switch. Replaced with a new switch and the microwave now works fine! Only thing that was tricky was that LG uses the hex screws with a peg in the middle to keep the microwave cover on. Had to use a small screwdriver and pliers (on the screwdriver) to unscrew the screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Perry, OH
- Parts Used:
- 6549W1S011M
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Microwave & turntable quit working-the computer worked ok.
Took off cover and checked all of circuits (& fuse). Had continuity until I got to turntable motor. Little motor on bottom of micro.It did not have continuity. I thought - looking at circuits - it had to be motor. When I got new motor - I was surprised there was no continuity through it but I was confident it was what I needed . But motor in & tested & worked fine. GE was no help at all! No useful info at all online! No schematics! The motor Had been discontinued ( thankks to info from Partselect.com). Partselect.com found a replacement part (& #).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from CRYSTAL LAKE, IL
- Parts Used:
- 6600W1K001C, 3B73362F
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Items were not getting heated up in the microwave,
Easy, and the microwave still doesn't work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cesar from Miami, FL
- Parts Used:
- 4370W1A006B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shaft socket was worn out
Pop old one out and replaced it with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Oak Ridge, TN
- Parts Used:
- 3B74133Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Microwave operated but did not heat
Initial failure of over range microwave Aug 3rd. Control Panel worked but no heat. Took to local LG authoriaed local repair place. They fixed it quickly and we re-installed it. Worked fine for 2 months then had similar failure again. Agaim took to same authorized repairer. They kept unit for 3 months but finally concluded theu could not fix it and suggested we contact LG for a partial refund. When they tested the unit during re-assembly in my presence, there was a blue flash and the fuse blew. Since we had built a custom tile mural back splash around this unit, I brought it home, ordered a number of time delay fuses new capacitor and two new high voltage diodes. However, using my Fluke DMM, I checked the existing capacitor and high voltage diode and they checked OK so I just replaced the time delay fuse. The high voltage transformer leads had 2 possible ways to connect to capacitor and diode. Tried one way, plugged unit in and turned it on, and immediatly blew the fuse. Replaced the fuse and reversed the high voltage transformer connections,amd turned unit pn, and it worked perfectly. Since we had experienced several power failures during the time of the original failure, the repairer concluded that power spikes might be at fault, so I also purchased a TrippLite ISOBAR4ULTRA 3300 Joule surge protector between wall outlet and microwave, and re-installed over range. It has worked perfectly since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marianne from CHURCH HILL, MD
- Parts Used:
- 6912W1Z004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
light bulb replacement
very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gena from ROSICLARE, IL
- Parts Used:
- 1B71961H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Tray ,Glass
Received my replacement Tray,Glass in only 2 days. Opened it and placed it in the Microwave. Yep, it was that easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Chesapeake, VA
- Parts Used:
- 2B71165R
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No Heat
1. Removed unit from the cabinet. (2 screws). 2. Remove the outer microwave metal shell. (10 screws). 3. Locate and remove part. (3 screws). 4. Install new part and replace all screws. 5. Install unit back into cabinet. So easy. I will share this site with all of my friends.
Was this instruction helpful to you?
Thank you for voting!
Had to lift on the door for the microwave to run, suspected the door switches.
Ordered the switches from Partselect, arrive in two days. Had trouble removing the plastic connectors from the old switch terminals, one of the plastic protectors broke, but was able to reuse it. It took a little figuring out how to remove the existing switches. Must push in a tab and rotate the switch on a little pin, then remove. Must be careful not to break the plastic tabs holding the switches in place. Replaced all (3) switches at the same time. All in all it was pretty easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Craig from Burke, VA
- Parts Used:
- 6912W1Z004B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light bulb burned out
I unscrewed the light cover, removed the burned out light bulb and replaced it with one I ordered on Partselect.com. It was very easy.
Was this instruction helpful to you?
Thank you for voting!