KESK901SSS02 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Leonard from Brazoria, TX
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Power block terminal failure
Ordered part needed. Much, much cheaper than purching a new range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Channelview, TX
- Parts Used:
- WP9761958
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
The Terminel Bloc Overheated And The Bloc Melted Causing The Stove To Cease Fukshioning
R&r
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NANCY from CARLTON, TX
- Parts Used:
- WP9760774
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broil element was shorted out and not working.
Removed four screws lowered element down and removed four wires being very careful, wires can slip back into the hole. Pull wires out of hole. Reattach new element and screw back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Roberts, MT
- Parts Used:
- WP9761958
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Wiring Block shorted due to moisture and Stove had no Power
This was very straight forward. Once the sheet metal shroud on the back side was removed just had to undo the one remaining wire, remove the block, and reassemble. Only question I had was which wires went where. The Wiring Block was melted due to the short and the wires were no longer attached. Did a quick google for a typical oven three-wire install and that did the trick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Grantsville, UT
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
terminal block back of range shorted and burned
EASY!! Repairs saved $300.00 on serviceman fees they will rip you off for this simple repare
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from MOSINEE, WI
- Parts Used:
- W10823692
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Duel Burner , Inside Burner Out
Removed burned out burner, replaced new burner tested works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from San Antonio, TX
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Contractors on my home did not tighten nuts on terminal block when installing. This caused an arch across terminal burning up unit .
Repair took 10 minutes time. Used Phillips screw driver and pulled terminal block off stove. Pulled wires off with socket set. Replaced terminal block and reattached wires and block to back of stove. I had called sears to order part and lady tried to sell me a 135 dollar part even though I advised her it was a terminal block. WOW I'm glad I know what I needed. That's when I went with parts select. Easy ordering delivered within five days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Aberdeen, NJ
- Parts Used:
- W10823692
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Center of Front Burner not heating up
Ceramic cooktop: Turn off power to the unit. remove long "locking" screws from underside of the unit; remove clips (may take a little effort if they are "frozen" in place) From underneath unit lift it up and out of the counter - do not try to lift from ceramic top- remove 4 control knobsun - remove 12 screws (3 per side) attaching ceramic top to the unit - carefully work ceramic top off the bottom frame; its a friction fit - do not force it. Place ceramic top in a safe, flat space. Note the orientation of the burner - you will need to replace the new one in the exact same orientation - also note the connections on the existing unit and match them to where they will go on the new unit. (note: my old unit had a black wire that was replaced by a solid metal strip) work the wire clips off the existing unit, flip it ove and note the number on the "clock face" where the spring clips attach. You may need to drill a small pilot hole from the top side. remove the spring clips from the old unit and place them on the new unit. These clips align the unit in the proper location and provide proper contact with the bottom of the ceramic top. Replace the top gentley working it onto the base and replace the 12 screws. Place the unit back in the countertop being careful to lift up to reposition so you don't disturb the foam tape along the edge of the opening. Replace the clips in the side of the unit, replace the mounting screws, replace the control knobs, turn power back on. You should be done. Takes about 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Christoval, TX
- Parts Used:
- W10823692
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dual element burned out
A breeze. Lifted top, propped it, removed defective element, disconnected wire modules,connected modules to new element, fastened new element, closed top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- benjamin from conway, SC
- Parts Used:
- WP4173175
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burned out oven bulb
unscrewed the top glass protector off and took the old bulb out and put the new bulb in. very easy - less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Spring, TX
- Parts Used:
- W10155557
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
While trying to tighten the oven door handle, the outside glass shattered.
I was not able to order just the glass, so I ordered the exterior door assembly. The door assembly is held in place by 5screws. 2 on top, 3 along the bottom. A very easy project!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louise from Humansville, MO
- Parts Used:
- WP9761958
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Terminal Block was melted where the cord had came lose.
Removed the therminal block and put the new one in.Using a screwdriver, very easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from cleveland, TX
- Parts Used:
- W10823699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner Would,Nt Heat Up.
Removed top of stove replaced heating element ,piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregg from West Grove, PA
- Parts Used:
- W10823697
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Left front did not work
Open oven door and remove two screews with 5/16 nutdriver to remove hole top of stove.Just lift up gently on front of top and pull toward you and when about 4 inch clearance on back of top you will see where all the wires connect ,press the side tabs of this big connector and it will release very easy to remove the top.Place top on bath towell upside down on countertop and remove 4 screws and 2 clips on the bad burner with the same 5/16 nut driver and remove the three wires and reinstall the same way then reinstall the top on the stove in the same order.Very Easy Job
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from king city, OR
- Parts Used:
- WP9759242
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
replace thermo fuse
turned breaker switch off. unscrewed the oven from the cabinet. lifted the oven out of the cabinet (heavy & awkward, needed an extra pair of hands). removed back panel. replaced fuse. reassembled everything. this is the second time i've had to replace the thermo fuse (oven blows the fuse when set to clean). first time i replaced the fuse it took about two hours. second time it about an hour.
Was this instruction helpful to you?
Thank you for voting!