KESK901SSS02 KitchenAid Range - Instructions

First we watched a YouTube on how to replace the thermostat. It was easy to turn off the circuit breaker. It was a little tricky to pull the range away from the wall and then we were able to unplug. Because our range is a dual fuel model, the back had a lot more screws to remove to get to the thermostat because there were covers over a lot of wires and the gas line I presume. However, we did get off the 12 or so screws with a regular screw driver. We easily located the thermostat and quickly realized that the two screws holding the thermostat in place were neither flat head nor phillips. We were able to remove one of them and merely twisted it sideways, installed the new thermostat with one screw and attached the wires. When we flipped the circuit breaker and plugged in the over, Voila, it worked. The hardest part was getting all the covers off the back. I hope it doesn't happen again because this was an expensive replacement part.

I used the digital multimeter for measure the voltage in the burner and in the digital part,I saw the electric cables

First I turned off the power. Next I disconnected the downdraft vent. Then I removed the cooktop knobs and turned it upside down on the counter. I then removed about 12 screws to remove the element housing. I then unsnapped the old element, disconnected the 3 wires, replaced it with the new element, replaced the housing and screws. I replaced the cooktop, reconnected the downdraft hose and turned on the power.

We removed 4 screws that let us raise the top of the stove. It was then very easy for my husband to remove the old burner and replace the new one. By ordering this part from you and installing it ourselves, we saved $248 from the quote we received from our "Maytag Repairman". Can't beat a deal like this and it was so easy.

received the part sooner than expected, all of the holes lined up, for being the first time working on a stove it could not have gone any better

Moved Oven from wall, removed eight screws holding down the Burner Top. Lifted Top and held it up to remove two screws on the side of the element. Disconnected four wires, replaced element, connected the four wires again and assembled in reverse mode of dissasembly. All went pretty simple, moving oven from wall and adjusting/level it back in place was the most time consuming.
Part works fine, delivery was faster than expected during the Holidays. Good Job Thanks!!!
HAPPY NEWYEAR!!!!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Unplug appliance first. Remove rear cover plate (only to disconnect burner plug). Remove plastic upper side covers. Open oven door & remove two screws holding burner top. Lift off entire top, flip upside down and change element.

We looked online for instructions, not sure how to "lift" the glass top.... There were 2 screws/hex head at the front of the range under the top that when removed allowed the top to be lifted up ..... the elements are on the underside, and with the removal of a few screws and unplugging the element connections (real easy) the burned out element was easily removed and the new one replaced... Less than 15 minutes for the whole operation...HOW COOL!

Removed the three screws holding on the back plate and removed plate.

Popped out the switch and used the pliers to pull off the wires. Connected the wires to the new switch.

Popped out the broken light. Slid the new lens into the front panel. Slid the light housing onto the new lens.

Re-attached the back plate.

Removed the therminal block and put the new one in.Using a screwdriver, very easy repair.

Removed top of stove replaced heating element ,piece of cake.

Ordered part needed. Much, much cheaper than purching a new range.

R&r

It was very easy. Disconnect the electricity. Take the two screws out that hold the top in place. Raise the top and with the pliers change all the electrical connections and retaining bars. Install the two new burned tops. Lower the top and re-install the two retaining screws.