KGRS807SSS00 KitchenAid Range - Instructions

Very simple. I removed two screws holding the oven in place. Slid oven out onto the kitchen floor - it doesn't really weigh that much. I then removed about a dozen screws holding the back panel in place. I removed the back panel, disconnected the thermostat by unscrewing a single screw and pulled the defective part from the connectors. I then installed the new thermostat, screwed the back panel back on, slid the oven back into place and re-secured with the two screws. Voila! Repair done. The whole procedure took about 15 minutes and was not difficult at all.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Getting at the part was difficult. The top and both side panels had to be removed to reach the blower. Once they were off, it was fairly easy to swap out the blower. The repair guy wanted $140 for the part and $160 to insall. I did it myself for $94! If you do it yourself, keep a good record of what screws came from where as you go. This makes re-assembly much easier.

Open oven dooor. With a philip screw driver remove the gasket plate at the bottom of the oven holding the seal gasket. pull seal gasket away from oven seal channel and clean surface before installing new seal. align seal pins to to seal channel holes be sure not to twist the seal insert pins in one at a time.Install lower bracket however you may want to wet the fray ends of the seal gasket prior to screwing in plate to keep the ends from moving away from the bracket when scrwing it in place.

My Kitchen Aid (Model KGR1801) gas range would not preheat. I did some online research and found that the gas range valve regulator is most likely the problem. I spoke to someone from a local appliance repair shop and he informed me that the gas valve is known to fail on this particular Kitchen Aid oven. I ordered the part from PartsSelect.com for a very reasonable price, received it the next morning by 10AM. In about 10 minutes I installed the gas valve and fired up the oven. I highly recommend PartsSelect.com.

Replaced oven temp sensor, removed oven door and interior racks for easy access to oven upper rear sensor access. Used philips head screw driver to remove both screws, gently pulled old senor out of reat oven wall until electrical connector clear of rear wall, disconnected connector, connected new sensor and gently pushed wiring and connector back into opening, reinstalled door and racks. Ran open thru cycle and used oven thermometer to check temp. fast easy install

The only problem was ordering the right part on-line.

First I cut off power ! 2 screws for oven trim,4 more to disconnect from cabinet. Hardest part was pulling oven out and pushing back in. I found a big box of correct size to rest it on so I didn't need to disconnect the powerline. 8 more screws to remove the back panel. 2 screws to remove the thermostat.Then put it back together. New part had arrived sooner than expected, cost of the part was less than a minimum service call would have been! I absolutly will use your site again.PS Wife was amazed and now thinks I'm a genious.

I first did a search with my issue, found out there were many others with the same issue. That then led me to see the part, a fuse / thermostat, was the culprit and easy to replace it seemed. But first called a service co. who confirmed my findings, and quoted a fix of a $2-300! So I bought the part; worse case I'd have someone else install. The web site noted the few screws to remove and a key suggestion to find a box of same height to easily slide out oven; I used a porter cable nail gun case which worked great. Took my time removing trim, mounting screws etc., slid out oven easy. Removed back plate and there was the older one. Removed and installed new in a minute. Spent more time cleaning around trim than actual install. What a great day it was. Wife was happy too!

The oven would only go into dehydrate mode. I called and they did some troubleshooting with me over the phone. We made our best guess at what part that I needed. They assured me if if didn't fix it I could return it. Good news is, that we got the correct part. The control board was the problem. Less than an hour to replace it. Phillips screw driver and turning the power at the breaker was all I needed to do. Super easy repair. Kind of expensive, but a oven/convet oven combo that can do self cleaning and dehydrating is worth repairing and keeping around for a while. Plus I not ready to redo my entire kitchen right now. I am very happy with Parts Select and would recommend them to anyone I know.

We don't have a repair story, but I was super impressed with the service! First I called KitchenAid and after 20 minutes on the phone, they could not find the replacement part for part of our stove top grill which broke. (The unit, BTW, is only 3 years old). Not only did you have it, but I received it the next day. Thank-you. Signed,A Customer for Life!

Shut off power at breaker and removed oven door to lessen weight. Removed oven trim and retaining screws and tried pulling out of cabinet. Stuck on power cable, so had to remove Mircrowave oven above to get to power cable plug. Removed oven back cover panel to access thermostat. Easy to unplug and replace with new thermostat. Reassembled and turned on power. Cooked dinner in oven.

I removed the two stainless trim pieces (2 screws) and then two screws which hold the oven frame to the cabinet. Be careful to put a pad on your floor before you pull the oven out of the cabinet as there are sharp edges on the bottom of the oven. I removed apprximately 12 screws holding the back panel in place. The fixed set point thermostat is in middle toward the top of the oven cavity after removing the rear panel. Just remove two screws and slide the terminal connectors onto the new thermostat. Very easy job for someone who is not too handy.

Repair was fairly simple, unscrewed oven from cabinet and pulled it out. Then remove screws on back panel to access the thermostat location. Unscrew old thermostat, unplug it from connectors and plug in new thermostat. Then screw back in place, replace cover and pop oven back in place. Now fire it up, worked for me! Thanks to part-select. Good luck everyone. Probably saved $200 service call.

Remove rear panel - remove sensor from inside - unplug from rear - reverse to install - did not fix problem