KERC607GBL0 KitchenAid Range - Instructions

Had to screw off old terminal block & screw on new one

One screw on each of the two cover plates removed, then element is pulled out enough to get at the connections. These are small blade connectors that slide off, two on each side, so 4 all together. The problem for me was that on one side the wires were to short and as soon as the blade connection was released the wire pulled back through the hole and was difficult to retrieve because it was hiding in the insulation. If I were to do this again I would use a small zip tie around the wire before disconnecting it so I would have something to pull it back out with.

Following the various instructions here made this replacement much easier! I was able to do this on my own with just a screwdriver. Pulling the hinges out was fiddly but after removing the screw and small hinge plate from each side a little wobbling and pulling with the door open an inch did the trick. After removing the door I started with the inside glass facing up on a table, and mid-replacement needed to flip the door over. So, recommend that you start with outside of door facing up. As you remove screws keep in mind where they came from so you can replace in reverse order properly. Other than that, everything went swimmingly! Thanks to everyone for their great advice.

I was not around the entire time a neighbor was working to get the door removed. He only said he had to remove an additional screw so I'm not sure I can be of much help here.Once the door was removed however, the repair went easily. I would tell anyone needing this repair to be prepared to clean a number of crevices around the door. I was glad to have a chance to clean these hidden places.Let me also said customer service rep was wonderful.

Removed rear panel (6 screws) and disconnected the four connectors on the Broil element. Then removed the 4 screws holding the the element to the top of the oven cavity. Inserted new element and connected the 4 screws to secure it. Connected the four connectors and re-installed the rear panel.

I was able to remove the door by opening it partially and lifting it up while jiggling it. Once off, I laid it with the inside up on a table and the screws along the bottom facing outward so I could access them easily. I removed the various screws and porcelain covers and sides feel of easily. The inside panel lifted off exposing the inner glass and frame. The screws and clips had to be sprayed with penetrating oil to remove them. The frame lifted off and the cracked glass was removed. I was careful to wipe away all the fluid used to loosen the frame clips. Assembly was the reverse of this being careful to let pieces fit nicely without force. It would have cost me $39 to have the repair performed assuming I could get the door off. A Phillip's head screwdriver was not adequate to remove the frame clips. You needed a correctly-fitting square drive.

The part came in 2 days even though I chose the least expensive shipping method. The hardest part was unscrewing the old screws that held the old bake element in place. We soaked them in WD40, and after a while were able to unscrew them. The new element slid in place and works just fine.

Took door apart no problem had a little trouble putting it back together just one piece I put back wrong had to start over not to bad still took less then one hour

I received the replacement broil element for my Kitchenaid model KESH307 range 34 hours after placing the order online with PartSelect.com! I had previously removed the old element and verified that the outer circuit was open. I did this without removing the oven door. I realized that to install the new element with the door on would require me to have 5 foot long arms and a very flexible 2 foot long neck.

Turns out there are at least 3 different styles of door mounting in the Kitchenaid line. I found the correct one for my range, and when the new element arrived, I had the door off in a jiffy. Enlisting my spouse to hold the oven door switch so as to keep the light off (It shown in my eyes.), I installed the new element with minimal difficulty. It took me about 20 minutes.

Thank you PartSelect for being there and for the really quick delivery.

pulled door up and out. Disassembled door. removed old glass and rope gasket. installed new glass and gasket.

Unscrew 3 screws across the front inside the oven door and the 2 screws on each side of the control panel. That allows for lifting the entire control panel from the front to access the switches from underneath. The old switch is held in place by the lug nut under the knob. Once removed, the 5 wires can be disconnected (carefully noting which wire connects to which terminal). The new switch is then connected, and then fastened back into place with the lug nut. The control panel is then re-secured by the five screws

Remove three Phillips screws underneath front edge, raise front edge and lay it back on stovetop. Pull knob straight off, use pliers to loosen nut holding switch in place, remove nut. I took photos of the old switch with wires attached that also showed the numbers on the terminals in case I pulled off too many at once. The new switch isn't arranged the same as the old one, but follow the conversion table, and it will work fine. Remove and replace one wire at a time. When replacing the control panel don't try to just lay it flat and slide it back on -- it won't work. Easier if you hold it at about 90 degrees and pivot it back onto the rubber seal at the edge of the stovetop. Re-install the three screws, and you're done. The new switch fixed the problem perfectly. I took apart the old switch and found a broken metal piece inside, so I was confident this was the problem, and not some other component.

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

We had been missing it for years. Perhaps it melted, maybe the dog. Anyway, Home Depot didnt have the match. I order the exact knob, received it in a very timely manner. Took it out of the package, and without any tool, placed it it it rightful spot. My wife is happy now. Thanks for helping me.

Turned breaker off. Removed oven door for access, two screws loosened element, unplugged wires from element & removed element. Reverse order to install. Perfect fit. Thanks.