KESH307GWH1 KitchenAid Range - Instructions

I received the replacement broil element for my Kitchenaid model KESH307 range 34 hours after placing the order online with PartSelect.com! I had previously removed the old element and verified that the outer circuit was open. I did this without removing the oven door. I realized that to install the new element with the door on would require me to have 5 foot long arms and a very flexible 2 foot long neck.

Turns out there are at least 3 different styles of door mounting in the Kitchenaid line. I found the correct one for my range, and when the new element arrived, I had the door off in a jiffy. Enlisting my spouse to hold the oven door switch so as to keep the light off (It shown in my eyes.), I installed the new element with minimal difficulty. It took me about 20 minutes.

Thank you PartSelect for being there and for the really quick delivery.

First of all I couldn't believe parts arrived next day. Parts solved the problem I was reluctant to believe new hinges would solve the problem. I installed the hinges in about 1 hour but I had door apart previously so I knew what I was doing. Now my wife is speaking to me again and she threw the wooden spoon away that she used to hold door closed. Just spent $100 dollars and saved $1600 thanks guys.

Had to screw off old terminal block & screw on new one

The burner infinte control switch was the same as the old one - just placed the wires in the same location - fixed the LED being on permanently. The dual serface element switch was a newer version. The difficultly i had was the connection labeling on the old switch. I was confusing the numbers with the wrong connections because the old switch had numbers where there were no connections, but I thought they went with two of my wires. I finally realized the wires went with the numbers on each side of the neutral. Ignore the numbers on each side, in the middle of the sides. Sorry, forgot the numbers and the switch is long gone in the trash.

Following the various instructions here made this replacement much easier! I was able to do this on my own with just a screwdriver. Pulling the hinges out was fiddly but after removing the screw and small hinge plate from each side a little wobbling and pulling with the door open an inch did the trick. After removing the door I started with the inside glass facing up on a table, and mid-replacement needed to flip the door over. So, recommend that you start with outside of door facing up. As you remove screws keep in mind where they came from so you can replace in reverse order properly. Other than that, everything went swimmingly! Thanks to everyone for their great advice.

Sensor matched perfect, but had to pull large upper rear panel to find location. From there took a few minutes to reassemble back. Did not un hook gas but turned it off. Obviously unplugged power. Oven works fine.

One screw on each of the two cover plates removed, then element is pulled out enough to get at the connections. These are small blade connectors that slide off, two on each side, so 4 all together. The problem for me was that on one side the wires were to short and as soon as the blade connection was released the wire pulled back through the hole and was difficult to retrieve because it was hiding in the insulation. If I were to do this again I would use a small zip tie around the wire before disconnecting it so I would have something to pull it back out with.

Took door apart no problem had a little trouble putting it back together just one piece I put back wrong had to start over not to bad still took less then one hour

I was not around the entire time a neighbor was working to get the door removed. He only said he had to remove an additional screw so I'm not sure I can be of much help here.Once the door was removed however, the repair went easily. I would tell anyone needing this repair to be prepared to clean a number of crevices around the door. I was glad to have a chance to clean these hidden places.Let me also said customer service rep was wonderful.

Followed included instructions transfered wires from old dual burner switch to new dual burner switch per the instuctions the new switch did not look exactly like the original switch but the instructions tell you how to wire it up. It works fine now,

The repair was simple:
PartSelect always seems to have the parts you need and they get them to you quickly.
Baking element - I removed the two screws that hold the element to the back of the oven ( Philips head). Disconnected the spade type electrical connections from each end of the element. Note: use some type of clamp to hold the wires from pulling back into the outer section of the oven. I used wooden clothespins). Reverse the process to install new element.
Broiler element - I placed the shipping container over the new baking element to protect it. Then removed the four screws holding the top element to the back of the oven ( Philips head). Take care to mark the 4 wires for the broiler element. ( 2 for outer coil & 2 for inner coil) Clamp these wires also after disconnecting. Slide the 2 "L" shaped hangers out of there slots. When installing the new element connect the wires first then slide the "L" shaped hangers back into the slots. reinstall the 4 screws and your done. I did the repair with out removing the oven door ( ours is difficult to get back on ) with the door off the job will take less time and access will be easier.

The oven light gasket had deteriorated with time and bulb changes. It is a self cleaning oven, which gets very hot during the cleaning cycle. The oven is old (27years) and off the "books" I selected a similar, but slightly smaller gasket (3" OD), and "fit" it to the 3.5" light fixture of the older oven. The gasket material was similar to the original, and I used a usable portion of the original,along with the new gasket to build a gasket for the light lense. Several years prior to this repair, I replaced the oven door springs. Whirlpool, who had taken over what was left of Chambers, had the springs. I did replace one heating element about 15 years ago. The Chamber's salesman told me that the Chambers was the "Cadillac" of all ovens, and it seems to keep running.

I followed the instructions submitted by other users which were helpful. Two notes that might help someone. 1. To loosen the screws holding the inner door glass, use channel lock type pliers to slightly twist the square bracket the screw is holding. The screw comes out easily then. 2. Note that the flange on the side rails go UNDER the glass door front. I spent quite a bit of time trying to get screw holes lined up with the flanges on top - DUH!

That should have been an easy repair according to previous responders that replaced this part.

The first issue is the Phillips head screw that fastens the sensor to the back of the oven was frozen and I had to drill it out.

The second issue was I could not pull the connector through the hole where the sensor wires pass. I decided to cut the sensor wires and use wire connectors to attach the sensor as instructed in the sheet provided with the sensor.

NOTE: You MUST use third party "gray" colored wire connectors that you can purchase in a hardware store. - the connectors provided DO NOT have a metal insert and even after several attempts would not grab the wires.

Another caution is you should use a self-tapping sheet metal screw to fasten the sensor to the oven wall if you encounter the same frozen screw that I did!

After I installed the sensor I tested the oven but found that this DID NOT solve the problem! I needed to order the "hidden" bake element that is mounted under the bottom oven wall and also the broil/bake element that is mounted inside of the oven on the top. See my comments for the Bake Element (bottom)

Had difficulty removing the two screws holding element(range is eighteen years old.Screws were badly rusted)After that,it was a piece of cake