KESC307HBT0 KitchenAid Range - Instructions

I received the replacement broil element for my Kitchenaid model KESH307 range 34 hours after placing the order online with PartSelect.com! I had previously removed the old element and verified that the outer circuit was open. I did this without removing the oven door. I realized that to install the new element with the door on would require me to have 5 foot long arms and a very flexible 2 foot long neck.

Turns out there are at least 3 different styles of door mounting in the Kitchenaid line. I found the correct one for my range, and when the new element arrived, I had the door off in a jiffy. Enlisting my spouse to hold the oven door switch so as to keep the light off (It shown in my eyes.), I installed the new element with minimal difficulty. It took me about 20 minutes.

Thank you PartSelect for being there and for the really quick delivery.

I watched the video, purchased the correct heating element and did the repair as illustrated in the video. I simply removed the cook top, removed the ground wire, removed the wiring harness, removed the failed heating element, installed the new heating element and reinstalled the wiring. Piece of cake!

I did the repair myself while my husband was at work. I lacked the brute strength to remove the door, so I ended up taking in apart while it was in place. Unfortunately, I only now noticed that instructions for installation were provided on your website. I did it without instruction, just making sure to note where screws had been removed so I'd be able to reassemble the works when I was finished. The worst part was loosening a couple of the innermost screws--even after a long soak in wd40, they were really hard to crack loose. Once I managed that, though, it went smoothly. Don't be intimidated; you can do this stuff yourself without calling--and paying--a repairman.

The burner infinte control switch was the same as the old one - just placed the wires in the same location - fixed the LED being on permanently. The dual serface element switch was a newer version. The difficultly i had was the connection labeling on the old switch. I was confusing the numbers with the wrong connections because the old switch had numbers where there were no connections, but I thought they went with two of my wires. I finally realized the wires went with the numbers on each side of the neutral. Ignore the numbers on each side, in the middle of the sides. Sorry, forgot the numbers and the switch is long gone in the trash.

One screw on each of the two cover plates removed, then element is pulled out enough to get at the connections. These are small blade connectors that slide off, two on each side, so 4 all together. The problem for me was that on one side the wires were to short and as soon as the blade connection was released the wire pulled back through the hole and was difficult to retrieve because it was hiding in the insulation. If I were to do this again I would use a small zip tie around the wire before disconnecting it so I would have something to pull it back out with.

I was not around the entire time a neighbor was working to get the door removed. He only said he had to remove an additional screw so I'm not sure I can be of much help here.Once the door was removed however, the repair went easily. I would tell anyone needing this repair to be prepared to clean a number of crevices around the door. I was glad to have a chance to clean these hidden places.Let me also said customer service rep was wonderful.

The new switch pin configuration differed from the old switch but the instructions were clear on the conversion. Would have gone quicker but I reviewed about 10 times before turning on the power just to be safe.

I did the repair following your instructions and it went very well. Now the temperature is working good , but the oven is heating up very slow. So now what should I do to fix the oven?

The range top came off with two screws under the front portion of the glass top (by the oven door). I unplugged the connection plugs at the rear off the range top, unscrewed the rear screws holding the heating unit in place and plugged in new element and reassembled range unit. You need to removed the two phillip head screws at the rear of the range top in order to remove the bar holding the heating element. Once you do this it is very easy to finish the job.

pulled door up and out. Disassembled door. removed old glass and rope gasket. installed new glass and gasket.

Removed rear panel (6 screws) and disconnected the four connectors on the Broil element. Then removed the 4 screws holding the the element to the top of the oven cavity. Inserted new element and connected the 4 screws to secure it. Connected the four connectors and re-installed the rear panel.

Unscrew 3 screws across the front inside the oven door and the 2 screws on each side of the control panel. That allows for lifting the entire control panel from the front to access the switches from underneath. The old switch is held in place by the lug nut under the knob. Once removed, the 5 wires can be disconnected (carefully noting which wire connects to which terminal). The new switch is then connected, and then fastened back into place with the lug nut. The control panel is then re-secured by the five screws

Removed the right side panel, lifted up insulation, removed element and replaced with new.

Remove three Phillips screws underneath front edge, raise front edge and lay it back on stovetop. Pull knob straight off, use pliers to loosen nut holding switch in place, remove nut. I took photos of the old switch with wires attached that also showed the numbers on the terminals in case I pulled off too many at once. The new switch isn't arranged the same as the old one, but follow the conversion table, and it will work fine. Remove and replace one wire at a time. When replacing the control panel don't try to just lay it flat and slide it back on -- it won't work. Easier if you hold it at about 90 degrees and pivot it back onto the rubber seal at the edge of the stovetop. Re-install the three screws, and you're done. The new switch fixed the problem perfectly. I took apart the old switch and found a broken metal piece inside, so I was confident this was the problem, and not some other component.

Removed the back access panel of the stove. Removed 2 screws holding the temp sensor, replaced temp sensor, Installed back panel. Done 19 minutes.