KDDT207AWH0 KitchenAid Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from ENID, OK
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven light kept burning out instantly
Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.
The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.
I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.
Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annette from GOLDEN, CO
- Parts Used:
- WP3181304
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Surface Burner Knob stem was cracked
Removed cracked know and replaced it with a new knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heriberto from AUSTIN, TX
- Parts Used:
- WP8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
THE OVEN WAS NOT HEATING TO DESIRED TEMPERATURE
DISCONNECTED POWER AND GAS TO THE RANGE. REMOVED 6 SCREWS FROM REAR OF THE RANGE. REMOVED THE 2 SCREWS HOLDING THE TEMPERATURE SENSOR IN PLACE. DISCONNECTED THE LEAD FOR THE SENSOR. INSTALLED NEW SENSOR IN REVERSE ORDER. OVEN WORKING PROPERLY NOW.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from COVINGTON, GA
- Parts Used:
- WP8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Stove got way too hot
Took the back off the stove, removed 2 screws, unclipped the bad sensor, clipped the new one on, put the screws back in and the back of the stove back on and that was it - 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from HOUSTON, TX
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
wire came loose and shorted out
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from LEBANON, VA
- Parts Used:
- W11594027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Light would not light
Pop old one out and new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norman from Tustin, CA
- Parts Used:
- WP3180081
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
backing for stovetop knobs
the decorative backings on our stovetop knobs had become frayed, and I simply pried off the old ones,and installed the new ones. I have use Parts Select for years for various parts replacement, their service is quick and accurate. When I need a part, I always check here first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from Levittown, NY
- Parts Used:
- WP3169203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The glass had broken
My son ordered the part, which came very fast,
It was a perfect fit, and the job went very smooth. I have no story to tell except that Mom was happy to have the oven again and a VERY helpful son!!!!
It was a perfect fit, and the job went very smooth. I have no story to tell except that Mom was happy to have the oven again and a VERY helpful son!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Elcho, WI
- Parts Used:
- WP3169203
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Replaced inner oven glass and reconnected the self cleaning lever.
The replacement of the glass was easy, I removed the door and placed on work bench. As long as you lay the parts out in an orderly manner the reassembly goes pretty good. The longest time was cleaning the glass's that were dirty from the inner broken glass.
I also reconnected the self cleaning oven lever this required the removal of the oven top. Lot of screws to remove but went ok. I put locktite on the two screws which are extremely short.
I also reconnected the self cleaning oven lever this required the removal of the oven top. Lot of screws to remove but went ok. I put locktite on the two screws which are extremely short.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Palm Coast, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
I snapped a bolt on the main power terminal block when connecting the pigtail.
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from Casper, WY
- Parts Used:
- WP3181305
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old knob stems cracked/broken
Pulled off the old and pushed on the new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald H from O Fallon, IL
- Parts Used:
- WP3169203
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Glass closest to oven in oven door was broken
First, I removed the oven door by pulling it open to where it loocked and then I pulled it up and off the hinges. Second, I removed the two screws on the top of the door and three screws on the bottom ot the door which allowed me to remove the front of the door. Third, using a nut driver, I removed the frame holding the inner glass to the door and removed that. Fourth, I removed the frame holding the broken glass to the door by removing the screws using my nut driver. I carefully removed the broken glass and vacuumed the channel that had the gasket in it. The gasket was fine so I did not have to replace it and will return it. I placed the glass in the frame on the gasket and reassembled the door in reverse order of how I had disassembled. All went smooth as silk.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Gaylord, MI
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
oven light not working
replaced light socket but did not repair problem. must have burned the motherboard.
pleased with service from your company.
pleased with service from your company.
Was this instruction helpful to you?
Thank you for voting!