21243 (1988) Kenmore Range - Instructions

We watched the video demo & followed it step by step. The project took about 35 minutes and we replaced the hinge on each side of the oven. First we removed the oven from the wall, then dismantled it & cleaned it thoroughly, removed the old hinges and replaced with new ones. the only problem we had was that the pin holding the hinge open was missing on one of the hinges, but we cut a nail and inserted it to hold the hinge open. The job was completed quickly, and the oven door fits and works well. Thanks for the video--it really helped us.

Left door attached to range. Took out all screws on door to get to the door seal. Cleaned parts as I went. Took out old seal and laid new seal in. Had to get two more hands to hold the parts and glass together while screwing it back together. Only hard part was remembering which screws went where. Looks and works like new. So glad I did it, as it has needed it for a long time. Easy even for a 70 year old female. PartSelect had the best price even with shipping. Thanks

I had repair men replace the door hinges 2times and decided the 3rd time to do it myself and save some $. ordering was a chinch, received the parts in 2 days and followed instructions posted on this site. They were excellent. Just a few things I would stress: Lift UP the door to remove, not open the door fully and pull out and also make sure to take the small pins out of the new hinges before closing. They are so small you could over look them. The person who put detailed instructions on this site is to be commended for clarity and detail on "How To" I really appreciated it.

For those with an older Jenn-Air, this range has stood up under the test of time and is still in good condition. We even called Jenn-Air for the parts and they no longer carry the oven door seal for this make. Thank you PartSelect for carrying the seal. We did call in a repair man and are glad we did as taking apart the door was quite involved. We were very blessed to locate a repair man who did Jenn-Air and are very pleased with the repair.

Called Sears as they will install parts you have purchased. I am a 67 yr. old woman. Already had the new element. Cut my cost by almost 2/3rds as other companies charged a fortune to guarantee their own work with their own parts..Which they probably get from you!!!

My 31 yr. old grandson very carefully took the whole door apart. Took out the broken window and put the new one back in. He was very careful to put every screw back in the original hole. It took him exactly one hour.

The repair was straight forward. Remove about a million screws and several layers. The only challenge was loosening some baked on screws in the innermost layer. Repair would have been less than an hour if not for those screws. Key advice is to pay attention to the order that each layer went back on. My oven/stove is about 25 years old, but works great. The part was backordered at a local appliance part store from May to ???. I ordered it at PartSelect and it was also backordered for a couple of months. I got it delivered to my home from PartSelect before it ever came in from the local store.

The basic replacement of the bad seal went fairly well. Just had to follow the other guidance and pay close attention to the correct sequence so that the door goes back together as it should be. The only real difficult part was when attempting to hold the hinge downward so that the door could be properly placed back on the hinges. After closer examination I discovered that there were two holes in each of the hinges that when they were opened all the way that the holes lined up and I cut off two nails approx 2 inches long and then once I was able to pry the two hinges all the way opened and then I used them to slip in through the two holes and they worked just fine and they held the door open, until the door could be re-installed. Once installed the nail/pins could be easily removed with some needle nose pliers.

Replaced oven gasket and both oven hinges. Repairs did not work. Oven door is actually worst. Do not waste your time replacing the oven hinges unless they are actually broken. When to Ace hardware and bought a package of 3 super magnets for about $10. Practice placing the magnets on metal strip on outside of the actual oven vs the oven door. This metal strip is not galvanized for which the oven cleaning latch goes through. Appeared to solve the problem. I then used epoxy glue to insure the super magnets would permanently stay in place. These are dangerous magnets that must be kept away from children and pets. You will spend more time separating these magnets from each other than gluing them in place. This part I will let you figure out but the only way to separate the 3 magnets from each other is the slide them, one at a time, from each other. Now I am awaiting 4 to 6 hours for the epoxy to cure. Best of luck. Jeff

We took the door off, you have to be careful of the hinges popping back. We put small screwdrivers on each side and held the hinges out, this made the door easy to just stand up and slide back on the hinges. The glass replacement was simple just a few screws. We spent $127.00 on the part and shipping and a new wall oven would have cost us $1500.00. Thanks for making this part available.

Removed the screws from the back of the oven to remove the damaged element; removed the electrical connectors and reattached to the new element and screwed it back in

In my 26 year old oven the screws to remove the element were extremely difficult to remove, but with 6-10 applications of Liquid Wrench and brute strength we finally did. We were a bit concerned with the insulation that was protruding but used electrical tape to secure the wires to the leads for good measure. All was successfull. I love my Jenn-Aire double oven!

Removed the door by unscrewing two screws holding it to the springs. Then I placed the door face down on a counter top. I removed the screws from each layer of the door and turned each layer over and laid it beside the door. Took care to support glass so it did not fall out and break. When I got to the layer where the seal was, I removed the old seal and replaced it with the new one. Then, I replaced each layer in reverse order. You have to be careful when replacing the layer that goes over the seal that the seal remains in the right place. It has a tendency to slip out of place, so check it before tightening screws. To place the door back on the spring loaded handles, prop the handles open a ways with screw driver handles. This provides a gap so that the door will slip on easily

Took the oven door off hinge. Took door apart pulled off old seal from inside of the inside panel of door. Replaced with new seal.

Unlike many here, the oven door closed enough to come up to temperature quickly and I could not feel any heat escaping. The oven worked fine but the light stayed on because the door just wasn't snug enough. I watched the great how-to video and ordered the hinges. They arrived in two or three days! I set up a work space, cued up the video again and the new hinges were installed in just a few minutes! But the door would not close enough to turn the light off! I did some more googling around and found the magnet trick! I just happened to have the perfect size magnet from a broken souvenir magnet! and now the light stays off! I stuck the magnet (about the size of a nickel) inside the door opposite the light button. This won't help if you have serious problems with the oven door, but it works if the only problem is the light!