9116424190 Kenmore Range - Instructions

As others have described, the removal of the old bake element is easy, just undo screws in the mount holding it to the inside wall of oven and pull out, then disconnect wires.

The first thing I faced unique is that some of the old element melted on the walls of my oven. After scrubbing extensively, it was obvious that the majority of the melted element was permanently fused with the oven wall--although it doesn't seem to have affected oven performance so far.

Next since my range was made in 1982, the replacement bake element didn't exactly fit my unit. Several adjustments had to be made. The size and fuctionality of the new bake element matched my oven, however the wire connections and the oven wall mounting bracket and the spacing of the two ends of the element as it went thru the oven wall were very different and required extensive modifications.

I used the old mounting bracket from the old melted element to attach the new element since my oven wall opening and mounting holes matched the old element mount--NOT the new element mount. This required removing the old mount from the old element by means of a vice, hacksaw and wirecutters. It was necessary to examine the old element mount very carefully before I hacksawed it off the old element as it must be reconfigured onto the new element. It will be bent up somewhat while removing---be careful.

Then I reattached the old mount on the new element. This required carefully bending the new element ends to receive the old mount as they were spread too far apart in the new element configuration. After much trial and error bending with several types of wirecutters the old mount was secured to the new element and installed into the oven.

Now a new problem appeared--the element ends now stuck too far into the back wall of the oven, making them dangerously close to touching the exterior of the rear of the oven and remember these are bare, hot electric connections! Much time in trial bendings and repositioning of the new element with the old mount finally resulted in a successful mounting with the old mount and the new element in a way that safely kept the bare wire connections within the rear oven walls.

A final problem was encountered when the new element came with slide-on wire connectors while my old element had screws and holes to connect the wires together. I found a drill bit the size of the required screws and drilled holes in the new element's wire slide-on connectors so that I could use the screw connector system of my old element to connect my new element's wires together. It all worked and the oven is functional.

Piece of cake. Pulled range out, unplugged it, opened stove, unscrewed element from back of stove w/ socket wrench, pulled out 1/2 way, unplugged bad bake element from the 2 wires, plugged in new bake element in, reattached to back of oven, plugged in stove and it worked.

Turned off circuit breaker for Range. Removed the 2 screws holding element and pulled wires attached to the element through holes. Disconnected the wires and attached new element. Had problem with one wire springing back into hole used paper clip to fish it back out of hole and then connected 2nd wire to heating element. Turned breaker back on and tested. Baked a cake. MMMMMMMM.

Simply turned off the power (circuit box). Unscrewed the screws holding the element in place and detached the element from the wires. Replaced with the new element and replaced the screws. Turned the power back on. Easy as pie and saved lots of $$!

first i unplugged the stove to disconnect all power. next itried using pliers to unscrew the screws and was having a hard time so hubby got the adjustable wrench and it was much easier. after taking out the two screws, i pulled the element out about three inches and disconnected the element from the two wires that hold it in place. then i snapped the new element in place just as the old one was and reattached the element to the stove using the two screws. after assuring that element was secure, i turned my oven on to 300 degrees and voila!!! we're cookin again!!!

Remove dthe two screws and removed the element. Put the new element in and replaced the terminals and screws. Partselected is the fastest shippers on the net.

This was really easy considering what it would have cost to have a repair person come and do it - not to mention the wait time. I had to hunt around a little bit to find the right socket, but once I had that, I unscrewed the bolts in the back and slide the element out. TIP: make sure you turn off the electricity!!!!!!!!! The wires were a little stuck, but the oven is 11 years old, so it's to be expected. One of the wires came off behind the oven, but I used needle nose pliers and fished around until I grabbed it. I detached the wires, attached the new ones, turned the electricity on and it's been baking Christmas cookies ever since. BTW - the part came in 3 days. I was sooo happy I didn't have to wait for a repair person. Thanks for all of you who posted your comments online. That was just the encouragement I needed to try it myself!

I removed the 2 nuts and pulled the element out until I reached the disconnect and unhooked the elements from the wire. Replaced the new one in reverse order. It was great finding the part here after Sears said they no longer made the part.

shut power off to range, took 2 screws out, took 2 snap on clips off old element. put snap on clips on new element, put 2 screws back in, and turned breaker on.

This repair was idiot-proof. Removed 2 screws, unplugged the old part, plugged in the new one, and replaced the 2 screws.
Literally a 2 minute repair!!

First i turned off the main electricity for the oven. Then I removed the two screws with my socket wrench. Then i pulled the element out about 3 inches then disconnected the 2 wires that heated the element. I simply reversed the process to put in the new bake element and i was done.

AMAZING SHIPPING.Ordered on Friday,received saturday WITHOUT NEXT DAY COST.Amazing,worked perfect.

I installed the chrome drip bowl and plugged in the burner to make sure that it worked. Voila!! everything is now perfect and i have a happy renter. thank you so much for your fast delivery.

Two screws hold the element to the oven wall. two wires attached to the back of the element. very simple removal and replacement.

This is how I did it--but I would strongly recommend you do step 4 first, and skip step 3! Remember, because 240V circuits have 2 "hot" wires, they may be "hot" (120V to ground) even when switched off!

1. Removed the mounting screws with a nut driver.
2. Pulled out the old element. BARE lug connectors on loose wires came out with it.
3. Watched an impressive show of sparks.
4. TURNED OFF THE CIRCUIT BREAKER.
5. Separated the connectors. Had to use pliers on the one I "fried".
6. Connected new element (connectors pushed together easily.
7. Reattached with screws
8. Turned breaker back on.