2783018890 Kenmore Range - Instructions

I took out the racks, unscrewed the bottom cover, removed the bottom drawer, cut the leads for the igniter, removed the bad one, had a little difficulty installing the new one, the screws were a little longer than the old ones, and were a little hard to get at, rewired the the leads, and put everything back, and started it up and it worked great!

I open the oven, then pulled out the racks. I went on to remove the bottom pan by removing 2 screws from the back.. I then removed the broiler burner and disconnected the wires from the relay. I unscrewed the igniter and replaced it. I stripped the wires and connected the old connectors using the ceramic wire nuts. I put the burner back in place and connected the wiring.. I then trested the unit to make sure it worked . . .it did. I replaced the bottom pan and racks and once again made sure everything was working right.

Job done.

Part arrived day before thanksgiving bent old igniter back and forth till broke off then easily took out screws.Cut and strip old wire, screw on new ignighter this was tough to get a wrench on with the positioning but after connecting those wires and slappin the rest of the oven back together one turn of the temp knob told me thanksgiving was going to happen Thanks to part select I was lookin like a hero!

i removed the oven door and then the lower panel.the two screws holding the igniter were hard to access, so i removed the gas rail.this made the job much easier. the advice from other people on this website was very helpful and made the repair much easier.just remember to shutoff both the electric and gas supply.

removed screw from heat sheild, unpluged igniter and tested for 110v on wires feeding igniter (ok). removed bad igniter,ordered new one and installed with 2 - 1/4in. hex head screws. cut old male and female plug ends off old igniter, and wirenutted onto new igniter. turned on oven and it works fine. but noticed after oven burner lights, igniter stays on the whole time oven is on. I would think that it should go off when burner lites. Does anyone know if this is normal operation?

I took the old igniter out and replaced it with a new one.

Removed oven racks
Remove oven bottom
Remove 2 screws holding the glow coil onto the burner
Install the new glow coil with the furnished screws
Reinstalled the 2 wires back where you took them off

Replaced the old igniter with new one in 15 minutes. Popped the door off, took the bottom plate off, unscrewed the igniter and disconnected wires. Put the new igniter in and reversed the steps.....piece o'cake! Works great now!

Removed bottom tray of oven, removed ignighter, unplug two wires.

I removed the oven racks and the bottom cover. The bottom cover had 2 hand tight screws. Then I had to remove the silver sheet metal plate attached with 1 screw. Then I removed the 2 small screws that held the old Igniter in place. Then removed the 2 wire nuts connected to the oven wires. The new igniter fit in the same place as the old and I attached it using the same old screws. Then I connected the wires using the new wire nuts provided in the igniter kit. After testing the new igniter by turning the oven on to 200F, i replaced all the parts i removed including the silver plate the oven bottom and the racks.

I removed the bottom drawer from the oven, took my handy nut driver out and removed two screws from the round igniter. When it was loose from the oven I removed the two wire nuts conecting it to the power sourse, I reversed the process and it was working again. One thing did go wrong my wife made me clean the oven that wasn't part of my plan :)

Basically followed the instructions that others had posted. Removed the bad oven igniter by removing the two screws securing it to the burner. Attached the new ignitor and then spliced the new wires into the old wires with the ceramic nuts that came with new igniter.

The broiler still worked, so I knew the issue was not with the power or gas to the oven. It was easy to remove the inside bottom of the oven to look at the igniter and burner. 4 screws hold the oven bottom in place. After the igniter was in view, I turned on the oven to see if it glowed, which it did not. 2 more screws out and the igniter was loose. The two wires coming out of the igniter go through a hole in the back of the oven to a compartment below the oven. This compartment is accessed by removing the bottom drawer and removing a panel in the lower back of the oven held in by 4 screws. After disconnecting the wires, I attached a thin pull wire to them then pulled the igniter out through the oven door. The pull wires made it easy to feed the new igniter wires through the back of the oven. The rest is a reverse of the process.

Removed oven bottom panel. Removed lower drawer to access old igniter. Had to take a cover panel off to expose igniter. Unscrew two screws to remove igniter which was a bit awkward to reach. Then simply put new one in its place.

Moved stove out from wall and unplugged 110 cord. Removed broken igniter from broiler with nut driver. Removed protective cover from back of stove. Cut off plug from existing igniter wires on the back of the stove. Installed new igniter and fed wires trough to the back of stove and connected the wires with the supplied wire nuts. Reinstalled protective cover on the back of the stove. Plugged the 110 cord back in and returned stove back to the original location.