2783018890 Kenmore Range - Instructions

took the bottom plates off with philips screwdriver.(note) there are two plates..outter and inner..to get to the two screws on the igniter.Remove igniter(two nuts). Install new. Cut the wires from old(lower part of oven and rewire with porclain wire nuts.Very simple...Partselect was great too..very fast shipping. Will do buisness again.

This site provides excellent instructions and saved a lot of time and effort.

Replacing the part only requires basic skills and attention to detail. The kit I received included ceramic wire nuts to splice the new igniter to the old connections. Be sure to leave enough wire to mke the connections properly.

Removed old igniter coil by removing 2 small hex head bolts and pulling the two wire plug connectors (be sure to unplug the range). Installed new coil and connected the wires with the ceramic wire nuts supplied with the new part.

followed peoples advices and all went very smooth. make sure to undo bracket from behind bottom drawer as it will make your life much easier.

We found the part right away from the diagram provided by your web site. We located the part number easily, paid on line and received in part in two days. My husband fixed it. It was relatively easy. Saved us money to pay someone to fix it. It could easily cost us more than $200.

1) use screwdriver to remove screws securing lower pan in oven (screws are at back of oven)
2) remove lower pain to expose igniter and burner
3) remove lower storage drawer
4) disconnect 2 igniter wires from where they are attached underneath
5) use nutdriver to remove burner from above and below (this makes it easier to remove the igniter)
6) use nutdriver to remove the faulty igniter
7) cut off clips from faulty igniter leaving enough length to strip and then attach with ceramic caps to new igniter. (be sure you attach the right clip to the right wire)
8) reverse the process to install the new igniter.
20 minutes tops

I removed the bottom drawer, disconnected the wires and then using the socket driver removed the screws holding the burner in place from below. I then unscrewed the bottom plate of the oven from the top so I could get to the burner. I unscrewed the one screw still holding the burner in place. Disconnected the old igniter and then cut the cables at an appropriate length so I could re-use the connectors on new igniter. Spliced together using wire nuts provided, mounted new igniter to burner, put it all back together and it fired up like it was new.

I removed the oven grates and removed 2 screws that held the bottom pan in the oven to get easy access to the burner and igniter. Remove 2 screws that held the burner in place. Removed wire nuts. Removing burner allowed easy access to fasteners holding ignitre in place. Confirmed that the igniter was bad by checking the continuity. Ordered part later in the evening from parts select. Part was here 2nd morning after I ordered it. Installed, and checked to make sure igniter wasworking properely. When check confirmed igniter was working, replace oven components. Saved myself $100 or more by doing it myself rather than having a repairman out.

Using descriptions provided by others at this site, I replaced the old igniter with the new one very easily. Since this was the second time this oven has needed a new igniter, I did not need to cut the wires as described. Instead, I just disconnected the old igniter wires and rewired the new igniter wires. Replaced all the items I'd removed and the oven functions just fine.

I first checked the power by pushing oven button, I heard the relay make a sound " CLICK" ,I then knew it wasnt the power .I then removed the oven racks and then I removed the the two screws holding the pan in place. I hit the power button and noticed the ignitor did not glow as it should.I ordered the part and replaced it and had frozen pizza 20 minutes later.

Good friend said he could do it no problem at all!!!!!

1/4 inch nut driver & 9/16 open end to take the igniter off and pull the wires out of the back of the oven. Then take the wire nuts off and install the new igniter . Shove the wire nuts back in the hole. Reinstall the burner and covers. Total time is about a half hour no special skills needed. easy

The range still worked and the broiler still worked. I noticed that the ignitor for the broiler turned on and glowed a short time after starting the broiler. I dissembled the floor of the oven (just two screws) and tried the same for the oven, but the ignitor did not start or glow. I ordered the part. It was sent withing two days. It was easy to replace and the oven has worked well since. I recommend ordering the attachment fixture as well, in that taking apart the one that held the old ignitor immediately stripped a screw and I ended up bending the fixture and having to reshape it (the small extra cost will be very well worthwhile!)

I removed the oven burner while the igniter attached. put unit on my bench and changed the igniter and reinstalled the burner and reattached the wires to the supply terminals. Tested the unit and it lite up ok.

I removed the oven door, racks, and oven floor. That was easy, the floor had two thumb screws and one phillips/hex screw. I removed the lower drawer and the 2 covers above the drawer. The igniter was held in place by two phillips/hex screws. Had to manuver a bit to get the right angle to remove the screws. THE MOST IMPORTANT PART OF THE REPAIR, when you cut the two wires to remove the old igniter, cut them off as close to the old igniter module as possible. On my stove one of the wires on the new igniter was about an inch too short and I had to add a section of wire. Overall the whole job was easy. Keep track of screws as you remove them.