36275797000 Kenmore Range - Instructions

Most videos show getting to the igniter module from the front when in fact with this older GE its accessed through the back left corner from the backside. So easy, a few screws and I was in. Quick change out and all worked well again.

Step 1 pull the broiler completely out of the bottom of the oven. Step 2 unplug the igniter Step 3 remove 3 small screws to pull the burner tube completely out of the oven. Step 4 replace the igniter and repeat steps to install burner tube back into the oven.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Removed six screws on the back panel. Just switched six wires from the old to the new module. Stove burners work perfectly now.

I followed the video instructions on the site. I unplugged the power supply and turned off the gas supply. I then removed the plate out of the bottom of the oven to get to the igniter. Then I removed the screws and unplugged the igniter to remove the old part. I had to purchase two porcelain wire nuts because the new part connection did not match up with the old connection. The repairs were quite simple and I had my oven back and working in no time. I am glad I read the comments from others because I thought it was my gas control valve, but they were right it was my igniter. This saved me time and money.

First I removed the racks and oven bottom panel. Then I took out the two screws holding the ignighter unplugged the wire connection and removed the old ignighter, compared the old with the new one mounted it back with the two screws plugged it back in. Job finished in 15 minutes and oven back working again.

Unplugged the stove and pulled it out from the wall. Took the metal shield off the back of stove held by 2 screws. Unplugged the Molex connector for the igniter. unscrewed the round metal shield covering the opening where the igniter wires run to the back of the stove. Removed the 2 screws that held igniter bracket to the burner. Next, I pulled the wires and Molex connector through the opening. Installed new igniter in the reverse order. Be very careful with new igniter as they are very fragile and can break easily.

Removed the screws that held the shield in place. Then unplugged the igniter and removed the 2 screws that hold igniter in place. I had to cut the connector off the new igniter and wire nut the old connector on because of a different connector.
I then put everything back together and ooolaalaa, it worked!!!!!!!

Thanks for the quick service,
Tom

Removed oven racks, removed lower oven shelf panel by using a flathead screwdriver and removed two screws on the back edge of the panel. Removed flat style ignitor (two hex head screws)from the gas burner tube using a 3/16 nutdriver. Disconnected two wires from the ignitor. Removed the two pin connector from the new ignitor, stripped the insulation to expose about a 1/4 inch of bare wire at the ends of the wire where the connector was removed. Installed the ignitor to the gas burner tube using the 3/16 hexhead screws. Connected the wires using porcelain wire nuts. Re-installed the lower oven shelf panel, flathead screws and the oven racks. Oven worked as advertised.

I deturmined that the flame starter was not pulling enough amps to open the gas valve (safety valve) . pulled two hand screws and removed floor of oven exposing the flame bar and flame starter. removed two screws on flame starter. removed lower pan drawer and disconected the electrical plug for flame starter. replaced in reverse order. easy.

I found that it was a little easier to pull out the stove to do the electrical connections. First I pulled out the stove being very careful not to bend the gas line. I pulled out the wires and disconnected them. I removed the 2 screws that hold the igniter and compared it to the new one it matched. I hooked it back up with the 2 screws then did the wire connections pushed the stove back carefully and tested the new igniter it worked like new no more microwave dinners thanks parts select .com

was still using back burners while waiting for parts (after safety check). I unplugged the electric for the igniters, raised top, installed tubes, checked for leaks with soap solution, closed top, plugged in electric tested burners. Got a big hug and kiss from my wife.

I thought I was being a total girl and was afraid of fixing my oven myself, but when it took forever to get my landlord to come over and fix my oven I ordered the part, got it in three days, followed the directions online and fixed it myself! Easy, easy! Turned off the electric, switched off the gas, unscrewed 2 bolts, unplugged the old switch, screwed in the new switch, replugged it and turned on the stove. Roasted a chicken and baked bread within minutes!

had to take back off of oven because of the connector and the plug end insert had the wrong pin so i had to take it apart and use old ones then i put the assembly in /and put oven back together

Lift up work light cover. Remove lamp. Remove two screws from control panel. Lift up control panel. Pop out spark module from slots. Remove the 6 wires from module. Attach wires to new module - module has a diagram on it that shows where wires are attached. Push new module back into slots. Replace control panel cover, lamp, and work light. Now the burners light - the spark is MUCH stronger than before repair.