66598013801 Kenmore Range - Instructions

It's a straightforward remove and replace with two screws. The lower element is most likely to go with years of baking when bake pans overflow on to the element, It can be checked with an electrical probe for resistance and continuity. If the oven is preheating and the lower element doesn't heat that is definitive. We had it checked under the extended warranty but the tech wasn't thorough enough. The extended warranty is of questional value.

This was the easiest repair I have ever done. The element was shipped right away and I received it in about 3 or 4 days. 2 screws were removed and reinserted to replace the heating element.

1. Turned off the electrical power. 2. Removed 4 philips head screws two from hanger bracket two from oven burner. 3. When hanger bracket screws are removed the bracket can be slid forward off the burner element. 4. When the burner element screws are removed the burner can be pulled forward where the wires can be removed (they are push on connectors)I did not need pliers but you may need them to assist you. Make sure the wires don't fall down into the oven holes. Reattach wires to new burner. Reattach burner to oven rear wall. Reattach hanger bracket. Turn on the electrical power. Broil your self a steak for a job well done.

turned off the oven at the main breaker. removed the four screws...two in back and two on the upper holding breacket.
removed the element and disconnected the spade contacts by just pulling them apart. measured it. Compared measurements
with items in catalog. Found exact match, ordered it.
Put it in same as out only reverse.
easy.

I removed the two screws retaining the heating element with a phillips head screw driver. Then I pulled the element forward to expose the wire connectors, and disconnected the two wires. I connected the two wires to the new heating element, and secured the new heating element with the two screws.

Unscrewed two screws on oven’s back wall holding the element. Unscrewed two screws to remove element retainer from top of oven. Disconnected the wires from the defective element and connected to new element. Placed new element and tightened screws holding it to oven’s back wall and placed retainer on top of oven.

Took 5 minutes... I did it in my pajamas... after a heavy duty margarita!

Here's a tip: start from behind.

4 screws, removed old element and installed new.

I unscrewed 4 screws. 2 held the element into the back of the oven and 2 held a holding bracket to the top of the oven. I pulled the old element off the two wire brackets coming out of the back wall of the oven. Then I took the new element and reversed the process. Easy.

removed stove/oven back & disconnected 2 wires. Removed 2 screws holding element to back of oven & 2 screws holding retainer bracket. Replaced element reversed procedure.

Unplugged the oven range, it is a dual oven. Removed the 2 screws in the back to loosen the element. Removed the 2 screws that held the bracket that held the element. Removed the 10 screws in the back that holds the back panel and then disconnected the cables to the element. Installed the element in the reverse. Easy.

Removing the backplate afforded easy access to the element connections. A few screws inside the oven hold the element in place.

Care needs to be taken not to scratch the floor when the stove is slid out to get at the back of it. I put lexan strips on the floor for the feet to slide on.

Pulled unit from the wall and unplugged power cord. Removed the worn out broiler element from the upper oven compartment. Upon removal one of the wire connectors broke requiring removal of the back cover of the stove. Easily replaced the connector. Broiler element was ordered, reasonable price, and delivered surprisingly fast. Connected the element to the connectors, replaced the mounting screws inside, checked clearances on the rear of the unit and replaced the back panel. Plugged power in and tested perfectly. Mama is happy!!!

Highly recommend this company for replacement parts! I was able to find what I needed without having to have the part number and info. After ordering I received the part in 2 days and replaced it in less than 10 minutes! Super easy and great transaction.

Removed 2 screws and pulled the element forward. Slipped off the 2 wires from the element. Installed the new element reversing the procedure. Piece of cake!!