66578002802 Kenmore Range - Instructions

Removed the two screws pulled the element out and unhooked the wires then used one of the included adapters to reinstall the new sensor then screwed the two screws back in to secure the sensor. Everything works fine now.

Just remove the old for new

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

I disconnected the electrical power, but not the gas line, and pulled the oven unit away from the wall. I unscrewed the old temperature sensor mount and only realized then the simple configuration: A wire from the sensor runs through the back of the internal oven space to the back of the oven unit through a thin space filled with insulation. The old sensor was easy to disconnect behind the oven unit and pull the old sensor and wire forward through the opening in the oven. The most challenging part was threading the new sensor wire from the oven interior through the back of the oven unit. The instructions and comments provided on-line by previous customers was EXTREMELY helpful. I wish I could do many more household repairs like this!

First I took the door off and outside to dump the glass in the trash which I had some Kevlar gloves so not to get cut. Removed the three screws on the bottom trim piece and the two on the sides remove the outside face glass next remove the four screws that hold the next glass. This glass is in a frame there is bent tab on one corner unbend open frame and install inner glass close frame rebend tab and reinstall all the parts.

The feedback from other customers was excellent. It does come apart in layers, and it helped me to number each layer with a sticky note as I dismantled it. I also kept the screws for each layer right next to the layer, so that I knew how many screws each layer used. The only thing I can add is that the tabs to remove the innermost glass from the frame are on one of the shorter sides of the rectangular frame. The tabs are part of the frame, and when you bend them outward the side of the frame detaches and you can replace the glass easily. In addition to the #1 Philips screwdriver, all I needed was a pair of pliers to bend the tabs.

Remove the big back panel (5 phillips screws). Confirm voltage is present when attempting to start the oven by unplugging the PROPER ignitor. I say proper because initially I thought that the broil ignitor was the culprit. Very upper ignitor is the broiler ignitor and the next one down is the ignitor for the upper oven. You will notice that the ignitor plugs differ between broiler and oven. New ignitor should have a male end. Once I confirmed that voltage was present when attempting to turn on the upper oven and probing the ignitor terminal plug, I proceeded to remove the lower cover inside the oven (2 screws very front side) and remove the burner assembly. (First you'll need to remove the oven door, easy, just tilt out part way and slide it up and off of the rails). The ignitor is mounted to the burner assembly. It's inevitable, the 5/16 hex screws (x2) will absolutely strip out so make sure you have some extras on hand. Replace the ignitor, reinstall and you should be good to go! I've read that you shouldn't touch the element with your fingers as this will compromise the life of the ignitor. Good luck!

the repair was not difficult ,take time cause back panel has to be removed to gain access to unplug the temp sensor ,it appear to work but the digital clock still flash not all the timebut it should not flash , not sure that i have fixed it

Called a repairman who installed the piece of glass as the old piece was difficult to remove. Started project so I could clean the various glass pieces but was happy he came and finished the job. It took him over 30 minutes and like I said I had most of the door apart.

My first suggestion, after turning off the power to the unit, is to take the oven door off. Two simple screws and it's off! It makes getting to the temperature sensor much easier. I also moved the oven out so I could get access to the back to remove the rear panel. The ordered part came with two pigtails, neither of which fit my oven wiring harness. I cut one of them and the wiring from the faulty sensor, spliced them together with wire nuts and made my own connection harness. The new sensor went in with little effort. The wiring went together flawlessly with the spliced connection protected between the oven cavity and rear panel. Reattached the rear panel and the oven door, then slid the oven back into place. Turned on the electricity and back to normal! Problem resolved!!

Undid screws on front and some on the back and replaced part and put screws back on and it fixed the proble

I had to pull the range out from the wall and loosen the rear cover to free the connector for the sensor as it got stuck on a corner guide. Put the new sensor in, rear cover back on, range back in place and tested the oven. Oven heats fast now and keeps a more even temp. Makes me wonder how long I was trying to cook with a bad sensor.

Followed instructions I found online at the Maytag site.

I tried to take it out from the inside as the vidio shows. But it would not come out far enough. I pulled out the stove and removed back sheet metal panel. Unpluged the electric, Unhooked the temp sensor,pulled it out from the oven side. Put the new one through the hole,and rehooked it up. And got to clean up the dust and my missing oatmeal I spilled a while back. Turned it on. Checked it with a spare temp gage. Works so far.