9116047810 Kenmore Range - Instructions

Got the igniter ordered. Since the original igniter was still on the appliance, I had to cut the wires on the original igniter in order to be able to attach the new igniter with the wire connectors supplied. Make sure not to cut the wire on the original(defective) igniter too short because otherwise you will have to splice again.

Part arrived day before thanksgiving bent old igniter back and forth till broke off then easily took out screws.Cut and strip old wire, screw on new ignighter this was tough to get a wrench on with the positioning but after connecting those wires and slappin the rest of the oven back together one turn of the temp knob told me thanksgiving was going to happen Thanks to part select I was lookin like a hero!

With directions from the website as well as in the box, the repair was almost flawless. I needed to be a mouse with a 6mm box-end wrench.

I took out the racks, unscrewed the bottom cover, removed the bottom drawer, cut the leads for the igniter, removed the bad one, had a little difficulty installing the new one, the screws were a little longer than the old ones, and were a little hard to get at, rewired the the leads, and put everything back, and started it up and it worked great!

Moved stove out from wall and unplugged 110 cord. Removed broken igniter from broiler with nut driver. Removed protective cover from back of stove. Cut off plug from existing igniter wires on the back of the stove. Installed new igniter and fed wires trough to the back of stove and connected the wires with the supplied wire nuts. Reinstalled protective cover on the back of the stove. Plugged the 110 cord back in and returned stove back to the original location.

took the bottom plates off with philips screwdriver.(note) there are two plates..outter and inner..to get to the two screws on the igniter.Remove igniter(two nuts). Install new. Cut the wires from old(lower part of oven and rewire with porclain wire nuts.Very simple...Partselect was great too..very fast shipping. Will do buisness again.

I removed the oven burner while the igniter attached. put unit on my bench and changed the igniter and reinstalled the burner and reattached the wires to the supply terminals. Tested the unit and it lite up ok.

I removed the oven door, racks, and oven floor. That was easy, the floor had two thumb screws and one phillips/hex screw. I removed the lower drawer and the 2 covers above the drawer. The igniter was held in place by two phillips/hex screws. Had to manuver a bit to get the right angle to remove the screws. THE MOST IMPORTANT PART OF THE REPAIR, when you cut the two wires to remove the old igniter, cut them off as close to the old igniter module as possible. On my stove one of the wires on the new igniter was about an inch too short and I had to add a section of wire. Overall the whole job was easy. Keep track of screws as you remove them.

I removed the oven racks and the bottom cover. The bottom cover had 2 hand tight screws. Then I had to remove the silver sheet metal plate attached with 1 screw. Then I removed the 2 small screws that held the old Igniter in place. Then removed the 2 wire nuts connected to the oven wires. The new igniter fit in the same place as the old and I attached it using the same old screws. Then I connected the wires using the new wire nuts provided in the igniter kit. After testing the new igniter by turning the oven on to 200F, i replaced all the parts i removed including the silver plate the oven bottom and the racks.

Removed old igniter coil by removing 2 small hex head bolts and pulling the two wire plug connectors (be sure to unplug the range). Installed new coil and connected the wires with the ceramic wire nuts supplied with the new part.

Basically followed the instructions that others had posted. Removed the bad oven igniter by removing the two screws securing it to the burner. Attached the new ignitor and then spliced the new wires into the old wires with the ceramic nuts that came with new igniter.

i removed the oven door and then the lower panel.the two screws holding the igniter were hard to access, so i removed the gas rail.this made the job much easier. the advice from other people on this website was very helpful and made the repair much easier.just remember to shutoff both the electric and gas supply.

frist tested ignitor with meter removed ignitor order
part , I recieved to my surprise next day I'm a very happy person

The biggest problem is to get down low enough and far enough back to be able to reach the igniter. Other tan that , it was a simple affair.Unscrew the old one and detach the wire nuts and reverse the procedure for the installation and hope the gas valve has'nt been affected

1) use screwdriver to remove screws securing lower pan in oven (screws are at back of oven)
2) remove lower pain to expose igniter and burner
3) remove lower storage drawer
4) disconnect 2 igniter wires from where they are attached underneath
5) use nutdriver to remove burner from above and below (this makes it easier to remove the igniter)
6) use nutdriver to remove the faulty igniter
7) cut off clips from faulty igniter leaving enough length to strip and then attach with ceramic caps to new igniter. (be sure you attach the right clip to the right wire)
8) reverse the process to install the new igniter.
20 minutes tops