36291201001 Kenmore Range - Instructions

I used pliers to remove the hex bolts from the old burner element and pulled out the terminals by hand. I ordered my part and was slightly concerned because the part number was different (this due to my oven being so old I guess). After reading another repair story on this site, when I got my new part, I turned off the electricity to the range at the fuse box vs. unplugging the oven from the wall - because if I had pulled out the oven to access the plug, I would have had to re-caulk along the edges where it connects with my counter tops. I then slid the terminals into the female parts; this was a bit tricky because the female parts had receded behind the insulation in the hole in the back of the oven where they are located. I used small needle-nosed pliers to grab them and pull them forward enough to slide the new terminals in (by hand). I then put in the old hex bolts and used the pliers to tighten them. Flipped the fuse box switch and tried it out - worked great!

unplug it and plug the new one in

After watching the video and ordering the parts and searching for the right size socket (which took most of the time) and finding medical tape as I had no electrical tape I took of the back unhooked the terminals and following the wires to determine which ones needed to be replaced I followed the video instructions on reverse as my son had spliced new terminal blocks into the old wires I taped each new wire to the one it was replacing and pulled it through the back of the stove and into the front attached the new wires to the new block and pushed the clips on the other end of the wires to the knob boxes. I rolled up the excess wire and taped it securely with medical tape so it wouldn't unravel and be in the way when I reattached the back shield on the stove. After I repeated the process for the second terminal (I had two that kept shorting out) I reassembled the stove plugged it back into the wall and used both burners that night to cook dinner! I have had no problems with those burners since then. Really if you watch the video first and follow the instructions you should have no problems. It is really quite simple if someone hasn't tried to repair the problems without replacing the wires. Splicing new blocks into old wires just doesn't work. If I have this problem again, which I hope I don't, I will be confident in my ability to fix the problem myself. Thank you parts select for repair video and the parts.

I was very excited to get them in the mail but waited to install after a clean up but when I finally opened the box I found I only ordered 1 6 inch drip bowl. lol Now that I know they fit when I reorder I am ordering a who new set for later use.

Removed burners and existing drip bowls and installed new drip bowls and existing burners took approximately 15 minutes

The part that was ordered based on the shamanic wasn't the part that was needed for the repair. It was to short. I took the other screw for the other side and that screw was an inch longer than the screw that was ordered thru your company. I then went too a jar that I placed extra screws, nuts and bolts which l keep in my garage . I found a same length screw but a different head and it works perfectly fine. When I ordered the part from your company most of the parts did not have a photo of the part on file, or a description like how long the part is. I still ordered it because it should fit the make and model number that was posted on the shamanic that was showed to me on line.

Move range out from wall,unplug power supply,remove two screws from back wall of lower oven element unplug two wires,discard burned element.Install new element,plug two wires in,fasten two screws. Done

First I found the model number, but it's parts were under a different number. So I ordered what I thought was the right oven element, but it wasnt right . My husband couldnt get it to fit . Well he finaly found the right part number so we could order the right part. We returned the wrong part and got the right element. It went in perfectly and the oven is working just fine now. Remember to always look up the part number you need and then order it.

Unplug the range before opening the back panel and removed the wiring connection and replaced with the new one

pull out, push in

after removing element.I order part. part was inserted without problems . It was correct fit. I am now baking again. Thank you the quick services on the order.

This one is a really easy fix as I only had to plug the burner element into the slot. I was very pleased with the speed of the order and would order again if I need parts.

Thanks,
Cheryl

The repair was very simple removed old element by removing two screws and disconnecting the element from the wires and reinstalling the new one.

Was a piece of cake removed 2 screws, pulled element out. Pulled the wires ooff the old unit and put them on new unit and screwed it back in.

I have a GE Profile oven and the heating element on the bottom broke in two. I found the part on your website very easily. It was easy to see that I had the correct part. I ordered the new element and it came in about three days. I easily took off the old element, but I was really surprised because the new one didn't fit. The heating element itself was the correct size, but the holes didn't quite match up. As a matter of fact I had to take some tin snips and expand the hole at the back of the oven. That was the only hard part, but it was really difficult to lean in that far without putting too much weight on the door. Anyway, I opened the hole about an inch more, plugged it in, and now it works perfectly!