9119851191 Kenmore Range - Instructions

Ever the optimist, I'd replaced the burner on this relic of another time to no effect. That left the switch. You guys should know that when a burner element goes bad it can take out the switch. I should have put a meter on it. Wehn I looked for a replacement a few months ago there were still factory parts available, but they were $80 or so and I wasn't inclined to risk that on a 40 year old range. I offered to replace the raange for my daughter as a Christmas present but she like this old thing. It was an unusual size with a pan storage compartment on the left. I went on line and found this universal replacement for about $25 delivered. What the heck. I ordered it and it arrived within a week. I pulled the stove out, killed the breaker, pulled the knob off, used a nut driver to take ther rear panel off, two phillips screws under the knob hold the switch in. The terminals on the old switch are in a slightly different order but are clearly marked L1, L2, H1, H2 and P. The P is the power and has a smaller terminal so you can't put it on the wrong one. Just examine the old switch ( it was marked the same way) take off the L1 and put in on the L1 of the new switch and so on, make sure you use the correct knob adapter to fit your old knob and break the switch stem to the correct length. It will break easilly if you hold it with one pliers and break it with another. Screw the new switch in place with he old screws. At this point, I closed the breakers and tested it. It worked fine. I turned the breakers off again. Buttoned it up and slid the stove back into place. 20 minutes tops. Great product. Good for another forty years.

pushed on the new knobs.
thanks fore having the parts.

I could not believe how easy it was to repair my own oven! Honestly I was shocked. I pulled the oven out, unscrewed 7 screws, pulled the old element out, placed the new one in, replaced the screws and I was done. All I could think about was how much money I saved! Also, it took me about 15 minutes.

Replace part an wires

I ordered the replacement clips from this site and they arrived in a timely manner. The clips were perfect, but due to the age of the oven, the holes had elongated and the new clips kept falling out also. I modified the clips by widening the tips with a pair of pliers. They are holding just fine. I don't think the older clips could've withstood the modification.

New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!

Turned off the electricity to the ovens. Unscrewed the two screws holding the old bake element. Removed the old one by disconnecting the two wires and replaced the new element in it's place.

Removed old surface burners and replaced them by plugging in the new surface burners. Now they work GREAT! Parts ordered and received with-in 3 business days. Fed EX delivered parts in good order very quickly. We recommend PartSelect.com

All I had to do was pop the clamp on the top part of the heating element and push the clamp into the hole.

pulled range out, unplugged unit, took out 7 screws, unplugged the elements, reinstalled elements, replugged, and completed with the 7 screws back in place. The 30 minute time was replacing both the broiler and bake elements. The parts were also delivered in a very timely manner. Could not have been more pleased and was very cost effective.

Unscrewed the heating element from the inside back of the oven and removed the housing cover from the back of the stove to access the terminals. (The unit had arked and fused the terminal to the connector.) Installed the new unit and replaced the housing cover on the back and screwed the unit into the back of the oven. Works like a charm.

First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.

Installed new knobs, mom is happy!!

Alls well that ends well. General Electric changed the configuration of our Light bulb socket on our 1996 oven. It did not have a flange with two screws as the original. The new one, you will just connect it and twist it into place. It worked and we are very happy. Such wonderful people to deal with at this site. Our sincere thanks,
Richard and Shirley

replaced lights in refrigirator and freezer