21237 (1988) Kenmore Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- doug from magnolia, AK
- Parts Used:
- WPY04100020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bottom burner burned out
same
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Exchange, WV
- Parts Used:
- WP74008014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken hinge
Took the door apart and replaced the hinge, very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Saginaw, MI
- Parts Used:
- 866294
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My oven light would NOT shut off
Al lI had to do remove the oh swith & attach th e new on & push in place
It took about 5 min. to turn off the electric & to turn it back on.
Glen V
It took about 5 min. to turn off the electric & to turn it back on.
Glen V
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Spartanburg, SC
- Parts Used:
- WPY703499
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cleaned stove. When temperature knob was cleaned, temperature settings were wiped clean.
Received the part within 10 days and installed in less than 60 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wanda from Greenwood, SC
- Parts Used:
- 12200031
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Could Not Read Words Or Numbers On Knob!
Pulled old knobs off and put new ones on. Thanks and god bless! Wanda
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Antonio from Davie, FL
- Parts Used:
- WP74008014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door Hinge broken
I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DEBORA from YELM, WA
- Parts Used:
- WPY04100020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The element burned up.
My husband removed the old element and replaced it with the new one. I think he used a screw driver to remove and replace. The part shipped and arrive in 5 days. Quick and easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from Wildwood, MO
- Parts Used:
- WPY04100020
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned out bake element
The most difficult part of the repair was removing the two Phillips screws that attached the element to the back wall of the oven. With some WD40, and a hammer to tap on the screws through the screw driver (and several hours) the screws finally came loose. Once the screws were out it was a matter of removing the two wires connected to the element and reconnecting the wires to the new element. After removing the screws this job took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Agusta, GA
- Parts Used:
- WPY04100020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking Element burned out
Removed racks from oven, unscrewed two screws holding old element in place with philips head screw driver from the back wall of oven. Carefully pulled element from oven to expose connecting wires and then pulled two wires loose from old element. Reconnected wires on new element and carefully reinstalled element to rear of oven interior with two screws removed from original element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Riva, MD
- Parts Used:
- WPY04100020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Rupture of bake element through coating causing flaming and sparks in oven.
We removed the 2 screws at back of oven that hold element on, which took some doing as they were very rusted. We then pulled old element out; this proved a bit difficult because the ends of the old element were stuck in the insulation behind. We had to wiggle the old element back and forth a bit to get it loose from the insulation. Other than that, it was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kris from Murfreesboro, TN
- Parts Used:
- WP74008014
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven door didn't shut completely
We found the youtube video created by partselect.com and followed it. We took the door apart, cleaned the inside, removed the old hinges and replaced them with the new ones. Now the door works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vern from Sugar Land, TX
- Parts Used:
- WP701650
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door seals worn
Removed the door by unscrewing two screws holding it to the springs. Then I placed the door face down on a counter top. I removed the screws from each layer of the door and turned each layer over and laid it beside the door. Took care to support glass so it did not fall out and break. When I got to the layer where the seal was, I removed the old seal and replaced it with the new one. Then, I replaced each layer in reverse order. You have to be careful when replacing the layer that goes over the seal that the seal remains in the right place. It has a tendency to slip out of place, so check it before tightening screws. To place the door back on the spring loaded handles, prop the handles open a ways with screw driver handles. This provides a gap so that the door will slip on easily
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Crest Hill, IL
- Parts Used:
- WPY04100020
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
element had caught on fire
Removed the screws from the back of the oven to remove the damaged element; removed the electrical connectors and reattached to the new element and screwed it back in
Was this instruction helpful to you?
Thank you for voting!