20234 (1988) Kenmore Range - Instructions

First I turned off the circuit breaker at the control panel to my Jenn-Air stove-top. At 220-volts, don't take any chances with electricity!

Then I removed two screws that hold the burner switch panel in place and lifted up the panel to expose the wires that are connected to all 4 of the burner switches, the exhaust fan and pilot lights that indicate if a burner is turned on.

I used a circuit tester to determine that the power was indeed off to the switches. Again, it is extremely important to respect 220-volts of electricity.

I ensured that all of the wires were already labeled the same as the terminal connections on the switch (i.e. H-1, H-2, P, etc.). If they are not, label them yourself with masking tape around each wire. Then I removed each of the wires connected to the burned out switch with a pair of needle-nose pliers.

Next I removed the two screws attaching the burner switch to the panel.

To install the new switch, repeat all of these directions in reverse, making sure to attach each labeled wire to the correct terminal on the burner switch.

Turn the circuit back on at the circuit breaker. Then test the burner switch and see if the burner heats up. Hopefully, you'll be cooking in no time...............

Remove the screws from bottom of door to gain access to the hinge screws. Remove the bottom hinge screws and then open the door to gain access to the top hinge screws. CAUTION after removing the top screws close the door as far as possible while still griping the sides of the door. Pull up on the sides to remove the door from the stove. The springs are fully loaded if you have the door open all the way and try to lift up (like I did) the hinge will spring back and get your finger. Install the new hinge, put the door back into the oven, install all the screws and then remove the temporary rivet that comes installed in the new hinge.

- the fan/light switch was still functioning, but it fell into the cavity underneath, after years of use, heat and grease caused it to weaken.
- 4 wires came off the old switch, and went on the new one with ease.
- the only complication was in getting the clips off of the old ones, and getting the new clips onto the new one. otherwise, a piece of cake.

The hardest part of the repair was getting the old cruddy screws out of the old element. They were sort of "baked-in". Once we got the screws out the rest was really easy. Just inserted the element prongs & screwed the new ones in. Ordering & receiving the part was a snap...I would recommend your company to anyone. Thank you.

Unscrewed old cap, installed new

Unplugged grill element and plugged coil element.
Install was as easy as was ordering from PartSelect.com.
Price and availability plus timely delivery will make me a return customer.

1-Unplugged the old 2 burner element.
2-Plugged in the new element.
3-Elapsed time approx. 10 seconds.
4-It took longer to remove the new element from it's shipping
carton than it took to remove the old & install the new.

Replace filter

This was so easy, it's a replacement that just slides into the outlet at the back of the stove. Done, just like that.

slipped the old modules out and installed the new modules by slipping them into the cavity and into the electrical connection.

remove two screws, pull out element, diconnect two wires, toss old element,plug in wires to new element, replace two screws and viola- done

Now if you just sold faucet parts I'd be all set.

Removed two screws near the hinges and removed door and laid it on counter.
As we removed screws from each part of the door, we stacked the parts in the order removed. Tossed screws into a shallow pan for safekeeping.
Removed old seal and put new one in its place.
Reassembled parts in reverse order as I cleaned each one.
Put door back on the hinges and the job was done.
Would have been a much quicker job, but door had 24 years of dribbles down in it, and needed a good cleaning.

We ordered a new element also, as the old one had blown up. Very gratifying to know there were still parts for my favorite old range.

The hardest part was breaking the caulk seal between the range and the cabinet. An extra set of hands made the job easier, by holding the panel while I connected the switch. The switch was delivered promptly and I am very happy with Parts Select. I found the other repair stories very helpful.

Installing the new switch was EASY. However, removing the old switch was very difficult due to the nuts holding the switch in place being designed as clamps not threaded screws and nuts.

Cut power!
Removed old switch.Only problem was new switch had shifted the four 'spade' connectiors on back so when I was done fan and light switch was crossed.

Everything PartSelect had on their site was perfectly correct.

REALLY appreciated the way PartsSelect handled everything, I will be back for further help on other things.