21245 (1988) Kenmore Range - Instructions

Removed old element, 2 screws, cleaned oven , 60 minutes, replaced with new element, working like new, wife thoroughly impressed...

I pulled off the facia from the microwave/oven. Unscrewed the plate holding the microwave and slid out the microwave. The microwave and oven are a unit. I unscrewed the oven from the hole it sits in and slid out the oven and set it on a sturdy chair. Then I unscrewed (6 screws) the bracket that holds the microwave to the oven. After that I unscrewed (14 screws) the top sheetmetal plate on the oven and slid that around behind the oven. Then I unscrewed the grounding strap inside. Did the 2 screws on each side of the oven holding the fan unit and slid that out. Undid the 2 wires plugged into the motor and the 2 screws holding the fan motor. Then I slid off the fan from the old motor and slid it onto the new motor and reversed the whole process.

My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.

Removed door (that was the most difficult part)
Took out lots of screws to disassemble
Cleaned all the components that were now exposed
Put new seal in place
Put parts back together with screws
Put oven door back
Excellent!!

It would have been a very easy job if the one wire had not fallen inot the back. I could not reach it and fried to figure out how to get in the back to no avail. Finally I took a piece of wire coat hangerm and bent it and then fished it out. The packing around the hole compressed while I was trying to get the wire and I thought I wpuld have to replace it, but overnight it resumed its original size. It should have probably taken less than thirty minutes.

Removed the original element with a screwdriver and disconnected the 2 wires, it took about 2 minutes. Got online with PartSelect and easily matched a replacement part. Ordered the part and received it within a couple of days. Very impressed with the ease and quickness of the order processing and shipping. Took the new element and connected the wires, screwed the 2 screws back in, it took about 2 minutes. Turned on the oven to check and everything worked perfectly. Very happy with the overall experience with PartSelect. Thanks!

First, I tripped the oven circuit breaker. Then I removed the two screws that hold the element in place. Then I pulled the element out about 5 inches and disconnected the two wires. At first, I had to figure out how the wires would disconnect. Once I removed the heating element, I reversed the procedure, tightened the screws, reset the circuit breaker, and set the oven to bake. The element began to function, and I knew Imy efforts were successful.

repair was simple two screws

Checked the element to see if it was open or no
resistance, it was open
e.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

ordered new broiler pan

First I opened the oven door fully and secured the hinge in an open position by putting a pin in a hole in the hinge to keep it from closing. I used a drill bit as a pin. I removed the one screw from the door side of the hinge on both sides and removed the door. I them removed two screws from the hinge on the oven side. I replaced both hinges at the same time. The part I order was an exact match and now my oven door closes completely and very quietly. This is a very simple job that even a beginner can do.

The door came off easily after I removed the two hinge covers that are attached to the oven. Taking the door off can be done with one person but ideally two.

The new parts fit in perfectly and the hinge pin used for shipping comes out easiest with a pair or wire cutters (you do not cut it just grab it and pull).

After that, re-assemble the door and drop in place. It was a snap.

FYI...the shipping was ultra fast and the price was great.

No issues whatsover with the entire process.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.

It was easy to get apart. I drew out a schematic of where the wires were so I could put them back in the same place. I plugged them all back up and it worked! Only problem was, there was a dead mouse behind the panel! He had not chewed anything, so the unit just went out from age.