1039567811 Kenmore Range - Instructions

First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.

Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said it would take.

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

Replaced drip pans that the apartment Superintendent had in place with the correct drip pans and now cooking is beautiful again! No more uneven cooking on the stove top.

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

Removed burner from each one. removed drip bowl. Inserted new bowl. Replaced burner. Excellent help from order people so I got the correct bowl was irreplacable.

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

Removed the burner elements, removed and disposed of old drip pans, cleaned the area, relaced with new drip pans and replaced the burner elements. Verified all burners were level - good as the day it was new!

I did not do it, I instead had my neighbor put the gasket around the light lens cover and replace it. He considers himself a handy man, so it was easy for him.

Good directions

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

I broke the correct post from the new cluster of post selections and stuck it on. I had the kit for a couple of weeks before I realized that this was not an electrical problem. It would have been good of you to send only the new plastic post. That kit was intimidating for a 73 year old woman who lives in the country and does most of her own plumbing and other household repairs. The repair took less that one minute.

Replacement was simple. Old switch was easily removed. Once I swapped the wires from old to new we were in business. One thing I would do differently than the included directions called for. I wish I had waited until I had installed the new switch to set the shaft length. I snapped off one too many sections of the shaft after measuring the original shaft as recommended. If I had installed the replacement switch and then set the shaft length it would have been more accurate. Everything still works but one knob is now slightly lower than the other three.

Ordered the drip pan from ParSelect.com. Unplugged element and took out old pan. Placed new pan in and replaced element. For the first time in many years, the part fit.

My husband was able to easily remove and replace the switch and know with-in 15 minutes.