S120-C Jenn-Air Range - Instructions

My spouse calls me Mr. Breakit--and she's right. I was delighted to read others' accounts that this was easy, but I wasn't sure. When the part arrived, we had 1 hour before company arrived. I took two screws out of the plate (tight--I had to apply a lot of torque), slid the old piece out, attached the new piece, put the screws back in. Voila! (Oh, yeh, do remember to turn the juice off.) We were "cooking" in about ten minutes. So easy a caveman could do it. And I did.

"First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and removed the two wires." from the burned out element. I plugged in the new element, reinstalled the new element and, 10 minutes start to finish, the oven heats again.
So easy even I can do it. !!!

Since the motor is larger than the original, remove metal flange; shim one side of housing with 3 washers per screw and reseal..simple! Works great.

Removed the blower assy. Removed the motor. installed the new motor. Reassembled the blower assy. The problem I had was getting the proper clearance for the squirrel cage blower fan to rotate without rubbing on something. I had to make shims for the mounting flanges of the housing to get it to work. Took a lot of head scratching.

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

I didn't. Don't know how to get to light bulb to change it for this specific model

The oven that was in out newly purchased house was a JennAir and over 20yrs old. Worked ok, but as with any heating element, the performance wanes over time. I decided to replace the baking and broiling element...and the oven door seal while I was at it. Everything went well, it was a simply remove/replace. Then I bumped the oven door where it was leaning up against the fridge waiting to be reinstalled. Down it fell on the tile floor. SMASH! Tempered glass EVERYWHERE. Got online with PartSelect and ordered a replacement (very reasonable price). It arrived in 2 days...just like the elements. Replacement was easy. Thanks to PartSelect for having the parts in stock and delivering them in record time!

Motor (Blower Motor Kit) Part Number: PS1569907
No instructions are included in the package from PartSelect. Disassembly from the main housing was relatively simple. I found that paying VERY careful attention to how the original motor was wired and mounted would pay off in correct re-assembly, conquering motor vibration and rubbing. Most of my project time was spent cleaning the rotating blade wheel from 20 years of grease build-up. On tools, I would have appreciated the inclusion, or availability as an accessory, of a long-stem correct-size allen wrench (used in removal of the fan blade wheel.) The job went well, and probably saved me $200 in service call and labor.

First I removed the two screws that held the old element in place. Then I pulled the element out about 5 inches so I could reach and pull off the wire clips from the old element. I then attached the wire clips onto the new element and pushed back the wires into the insulated area and when the back plate matched up to the screw holes, I re-inserted the screws and tighten them down. The oven works great.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

As described elsewhere. If the two retaining screws are rusty, order new ones with the element. They are expensive, so take them out and check before placing the element order. Save time and shipping costs.

removed 4 screws holding burner controls. removed wires off old and placed on new burner control. very pleased with quick shippig of part. two days and range was as good as new. excellent company to buy from

Took the (6) screws holding the top of the stove out, then removed the switch screws(2). Then lifted the top, so as I could reach and get at the switch. And then I repeated the above. It was alot easier the second time. Duh I erred the first time and replaced the wrong one and before I relized it, I opened the switch to check out. All in all. I still got satisfaction from doing it myself. Thanks Parts Select

pull oven, remove back pannel and unplug and remove high limit switch. Repair was the reverse of removal.

Remove the screws from bottom of door to gain access to the hinge screws. Remove the bottom hinge screws and then open the door to gain access to the top hinge screws. CAUTION after removing the top screws close the door as far as possible while still griping the sides of the door. Pull up on the sides to remove the door from the stove. The springs are fully loaded if you have the door open all the way and try to lift up (like I did) the hinge will spring back and get your finger. Install the new hinge, put the door back into the oven, install all the screws and then remove the temporary rivet that comes installed in the new hinge.