JES9860CAB01 Jenn-Air Range - Instructions

unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

took the old one out (two phillips head screws)and put the new one in. done. took about 5-6 minutes.

Simply unpluged the old cartridges and plugged in the new ones, it could not have been easier. My 18 year old cooktop looks brand new. My old cartridges were black and the new ones are stainless, but, the look is good, since most new appliances are now stainless. The best part is that it cost less than half of what a new cooktop would have cost plus all of the mess that would have been made tearing out the old one and installing a new one. Thanks PartSelect, A Very Satisfied Customer.

Lifted out and unplugged grill. Plugged in and put in place new module. I tested it right then and it worked great!

replacement was very easy, took 5 min

unplug and plug in new

I needed two parts for the Jenn-Air stove that was in a house I was trying to get ready to sell. I didn't realize I needed the parts until the day before the house was to be listed. So, I was able to order from Parts Select and have the parts shipped overnight for an extra fee. They arrived the next morning. After opening the box, I realized the wrong color had been shipped. I called and the service I received was just awesome. The overnight shipping was refunded. And the right part was shipped out at no extra charge. I was told to keep the first part that had been shipped as well. The new part arrived the next day. Thumbs up for Parts Select! They are my new go-to-guy!

I thought the part might not be available. Ordered the part from PartSelect. Couldn't have been easier.

When burner insert arrived just plugged in. Piece of cake !

I simply removed the old cartridge by lifting it up and pulling the plug end out. I slid the new coil cartridge with the plug end in its place. The grill replacement was similar. Remove the grll grates, pull out the burner element from its plug position, remove the grill rocks and insert the new coil cartridge in its place. No tools or special skills required. It's like I now have a new cook top.

Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.

Watch the video. Spot on instructions. Easy peasy.

Remove the door.
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!

Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it easily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done