JES9900BAS20 Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Andrew from SAINT PAUL, MN
- Parts Used:
- WPW10310274
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Lower range burner element burned out
Should have been under the 'very easy' category, unscrew 2 screws, pull out old element, disconnect wires, reconnect new wires and screw back in. Unfortunately the right wire disconnected while pulling out the element, so I had to pull the the stove out, disconnecting vents in the process, then remove the back to be able to feed the wire back in thru the element hole . While back here I noticed that the reason the wire came off is that the way it was routed behind the stove cover was such that there was virtually no slack to be able to pull the element out in the first place. I'll bet that at the factory, the element was installed first, THEN the wires were connected. Whoever was on the line that day made extra sure of no slack in back, and that made the job take 5-6 times longer than it should have. As for the part replacement, it was a perfect match to the original part so it was super easy once the wire got back in the oven...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Buford from Sun City Center, FL
- Parts Used:
- W10823711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Element Burned out
looked for how to video on you tube. It saved me lots of money. Anyone could do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from Shelton, CT
- Parts Used:
- 74003645
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
glass pane was cracked during the cleaning process
needed to completely dis assemble the oven door to get to the inner pane of glass...took some time...I was able to do it on my own...could possibly go a little quicker with two people for a few of the steps...but possible by one...then reinserted the glass pane...and then need to re assemble the door layer by layer...up and working again...would have cost several hundred dollars if need to call a repair person in...this way was the cost of the piece..less than $70 ... and my time...well worth it....thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Ashland, OR
- Parts Used:
- WPW10162384
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Oven would stop heating after a few minutes of operation
Heat escaping from the top of the over door would overheat the electronics and cause the system to show error codes F1 and F3-1. Error code F3-1 suggests that the oven temperature sensor was bad. I replaced the sensor but that did not stop the problem. Replacing the oven door gasket stop the heat leak and solved the problem. I simply pull the old gasket off the door (it stuck a bit at the bottom but a pair of pliers solved that problem, then push the new gasket into place without any tools. The old gasket was very hard and non-complient where food had spilled on it and baked hard.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from CHAMBERLAIN, SD
- Parts Used:
- 12001656
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
my oven would not heat to proper temp
I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricky from JASPER, TX
- Parts Used:
- WPW10310274
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My old element finally went out
Easy peasy...1. Take 2 screws out to remove the back cover. 2. Unplug the 2 wires from the element. 3. Remove the 2 screw holding the element from inside the oven and take out the old element. Repeat the steps above in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Citrus Springs, FL
- Parts Used:
- W10823711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
I turned off the range breaker and doubled checked to make sure the power was off . Using 1/4" ratchet wrench I removed 2 sheet metal screws and lifted the glass top up and held it in up with a small cardboard bow. I removed 2 more screws holding the element in place and installed new unit. I then
See description listed as problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from SHELTON, WA
- Parts Used:
- WP74010824
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
nipple on infinite switch broken off
took off nobs, pulled stove out 2 inches to access front side screws,( has 1 philip screw on each side end and four nut screws under panel) pulled panel out and flipped forward and down, all switches exposed and took apart broken switch and installed new switch(PAY ATTENTION TO WIRING PATTERN), reverse order for install back. bingo!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Clermont, FL
- Parts Used:
- W10823711
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Burnt out burner
Had this range for 6 years. My daughter turned on the burner and it went "pop". She was very upset. I found the best price at PartSelect, and ordered the same day.
the first burner arrived broken in the box. We contacted PartSelect, and they immediately sent another and rushed shipping. It arrived in excellent condition.
To replace the unit: First, I turned off the circuit breaker for the range. Then I removed the two Philips screws that held the cooktop down. Next I removed the nut screws holding the burner to the cooktop.
Then I placed the new burner next to the old one, and one by one swapped the wires (this way I was sure I had the right wire on the right connector). One of the wire connectors broke when removing it from the old burner. PartSelect had provided 4 repacement connector pieces (oddly, all of which were too small for the burner element). So I located a replacement connector at a local hardware store. Stripped the end of the wire and used pliers to fasten the new connector.
After all connectors were secured to the new burner, I screwed the burner to the cooktop, then closed the cooktop and secured it with the two screws.
Turned on the circuit breaker, and it works like new! Saved over $100 by doing it myself!
the first burner arrived broken in the box. We contacted PartSelect, and they immediately sent another and rushed shipping. It arrived in excellent condition.
To replace the unit: First, I turned off the circuit breaker for the range. Then I removed the two Philips screws that held the cooktop down. Next I removed the nut screws holding the burner to the cooktop.
Then I placed the new burner next to the old one, and one by one swapped the wires (this way I was sure I had the right wire on the right connector). One of the wire connectors broke when removing it from the old burner. PartSelect had provided 4 repacement connector pieces (oddly, all of which were too small for the burner element). So I located a replacement connector at a local hardware store. Stripped the end of the wire and used pliers to fasten the new connector.
After all connectors were secured to the new burner, I screwed the burner to the cooktop, then closed the cooktop and secured it with the two screws.
Turned on the circuit breaker, and it works like new! Saved over $100 by doing it myself!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- valerie from lanoka harbor, NJ
- Parts Used:
- 74003645
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
inner glass on oven door cracked.
Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aubrey from EADS, TN
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven sensor caused cooling fan to run continuously. Had to flip breaker to get it to turn off..
Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Athens, OH
- Parts Used:
- 74003645
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Glass on inside of oven door cracked
I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.
I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.
I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Desmona from GONZALES, LA
- Parts Used:
- WPW10310274
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven would not heat past 200
First be sure to unplug stove or turn off from breaker switch. I Removed racks from oven . Using screwdriver I loosened the back plate in the oven that held the wires connected to heating element , being careful not to let wires fall through holes . Gently pull element tip apart from wire. Snap end of new element to wires, screw plates back to tighten
Turn oven on and check to assure heating properly. Very simple
Turn oven on and check to assure heating properly. Very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GLENA from CINCINNATI, OH
- Parts Used:
- W10823711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Burner Element Replaced
My grandson, age 15 did the replacement. Now, how easy is that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geraldine from Germantown, NY
- Parts Used:
- WP7801P173-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Racks were dark and dirty
The first set of racks did not fit. I called the Service rep, gave him the model number and exchanged the racks for the new ones. The new ones fit perfectly and the service was excellent. I would definitely recommend PartSelect.com to anyone who wants to deal with a company with excellent service, parts and representatives who know their stuff.
Was this instruction helpful to you?
Thank you for voting!