JGR8895BDS12 Jenn-Air Range - Instructions

The lower oven would not heat up, the temperature stayed at 100. I'm pretty sure the same instructions apply for the upper oven. This is a pretty straightforward repair with a couple of minor bear traps. 1) Remove the oven door by simply lifting it up off the hinges. Not absolutely necessary, but helpful to get your head inside the oven. Not a bad idea to vacuum out the oven floor at this stage. 2) Remove the two Philips head screws at the front of the burner pan cover - the screws are at the very bottom inside the oven. 3) The pan cover lifts straight out of the oven, set it to the side. 4) Remove the burner cover held down by either one or two wing nuts - my oven only had one wing nut from the factory - nice job Maytag on your quality control!! 5) Loosen the screw holding down the burner cover in the far back right corner. This cover is a steel rectangular box that is a shield for the burner gas / air connection. Turn the box around to expose the burner end. 6) Remove the two screws that hold down the burner assembly. One screw is at the very front of the oven. The other screw is on the left side of the burner at the rear. Do NOT remove the pan held down by 6 or more screws. On my oven, the left rear screw was stripped. It stripped in a very weird way that took a long time to remove it. The threads inside the metal were fine, but the threads that had been exposed to heat were brittle and fell off. That meant the screw backed out about 3/4 of the way and then kept turning. This is where pliers come in handy. It will take some pulling up and turning with pliers to get those stripped screws out. I didn't want to cut off the screw because the cut out part would fall back into the lower pan. 7) Pull the oven out from the wall and unplug it from the electicity. Remove the 3 screws holding the left rear metal panel in place. There are two screws along the far left side and one down lower on the right. The panel is connected to the one next to it with tabs. 8) Unplug the ignitor. There is a white fireproof wire that comes up from the bottom of the oven that plugs into a white automotive style clip connector. Push the tab to release the clip and unplug the wire. 9) Wrap some stray wire or string around the plug to use as a pull wire when reassembling the oven. 10) Go back to the front of the oven and lift out the burner, be careful not wo pull your pull wire all the way out of the oven. Untie the pull wire. 11) Remove the two philips head screws that hold the ignitor to the burner bracket. 12) Reassemble! Attach the new ignitor with the two screws. 13) Push the wire into the lower part of the oven. 14) Go to the back of the oven and pull the wire through the oven wall. 15) Drop the burner in, making sure it mates up with the gas tube in the back right. 16) Flip the rectangular burner shield back and tighten it down. 16) Replace the two screws that hold down the burner tube, front and rear. 17) Replace the burner shield with the wing nut(s). 18) Replace the burner cover, or floor of the oven. 19) Go to the back of the oven, plug in the ignitor wire. 20) Replace the rear panel cover and secure it with the three screws. JOB FINISHED! Plug in the stove and push it back. The oven takes a few minutes to start heating, you should be able to see orange glow around the slots in the floor of the oven.

Easy just loosened screws took apart door, removed broken glass and installed new glass.It took longer to clean the stove! Lol!

I had to use a dremel to grind the heads off the rusted in screws that hold the burners to the stove top then drill out the screws and use larger sheet metal screws to reassemble. Don't lift the stove top much with the burners attached or you'll bend the gas lines. Two screws inside the top oven hold the top down. Without the rusted screws it would be an easy job.

removing the screws holding the burner together was impossible. they snapped off and I had to drill them out. that took the most time. after that it was 100% easy hookup. clean up of the burner was done with a wire brush. good quality products. thanks.

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

I disconnected the electrical power, but not the gas line, and pulled the oven unit away from the wall. I unscrewed the old temperature sensor mount and only realized then the simple configuration: A wire from the sensor runs through the back of the internal oven space to the back of the oven unit through a thin space filled with insulation. The old sensor was easy to disconnect behind the oven unit and pull the old sensor and wire forward through the opening in the oven. The most challenging part was threading the new sensor wire from the oven interior through the back of the oven unit. The instructions and comments provided on-line by previous customers was EXTREMELY helpful. I wish I could do many more household repairs like this!

This repair is only if your old igniters are working but they are so cracked that the spark is not going where it should be. TURN OF THE GAS SUPPLY VALVE BEHIND THE STOVE AND UNPLUG THE STOVE FROM THE WALL.I had to drill out most of the old screws to remove the burners plates because of all the old baked on spills. I bought replacement screws when I bought the igniters because I felt this would be a problem. My repair time included scrubbing the stove top. Once all the parts that make up the stovetop burners were removed (NOTE WHICH BURNER PLATE CAME FROM WHICH LOCATION, THEY ARE DIFFERENT SIZES) and I could see the pipes beneath the stove top, I cleared off the top and used a spreading knife to push in the clips on the left and right sides near the front of the stove. It was thin enough to fit in the space between the stove top and main body. Push the clip inward and pull up on the stove top and it will let you lift the top. Be careful because it may release suddenly so be gentle. I also removed the top section of the back of the stove to access the igniter terminal block. A few screws, nothing more. Be sure to take note of which wire goes where. (They are color coded). Unplug the old igniters. it is easiest to cut he old igniters off of the end of the wires and pull out three wires leaving only one. At the back left of the top of the stove there is a rectangle channel that the wires are running through. There is a clip that holds the wires loosely together. Remove the wires from that clip or the next part will be difficult. Run each of the new igniter wires through their respective holes in the stove top. BE CAREFUL NOT TO DAMAGE THE WIRE INSULATION IN ANY WAY. When you put the burner plates back on the igniters will be sandwiched in between the plate and the stove top. Using electrical tape, tape the connector ends of the new wires to the one remaining old wire. Gently pull the old wire through the rectangle channel, pulling from the back of the stove. Take your time so no damage occurs. Once the wires are pulled, plug them in to their respective terminals and place the wires in the loose clip. Make sure the new wires are not crossing the pipe openings where the burners are located. You can close the stove top and double check there are no wires across any of the burner openings. Re-assemble the burners and plug in the stove. DO NOT OPEN THE GAS VALVE. Turn on the stove and check to make sure the new igniters are working properly and sparking to the burner plate assemblies. You should see a controlled spark. Do not touch the burner plates or igniters or you will be shocked. If all are working then you may put the back cover on and open the gas valve. If none are working make sure the stove is plugged in. If some are working then check the connection on the terminal block and the wire insulation. If they are still not working then you've got bigger fish to fry. Good luck my friend. Happy fixing!

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

Ordered the oven sensor. Two screws to remove to replace old sensor. Since this was a slide in unit, you had direct access to the wiring harness. Used the adaptor. Total repair time about 20 minutes. A very easy do-it-yourself project.

Slide oven door off hinges. Remove old gasket. Instal new gasket. Used eraser end of pencil to help feed in ends of gasket into respective holes for excess. Note: job could have been accomplished without taking off door but I wanted to take door appart to clean inside and out of glass.

Followed instructions I found online at the Maytag site.

It was necessary to take the decorative glass and metal safety panel off using a screwdriver in order to get to the frame that holds the safety glass. It was hard to slide the new glass into the frame without help from a second person to hold the other pane in place.This was an easy repair to make I would just suggest having 2 people to hole things in place while replacing screws.

I removed the sensor from the oven using a philip screw driver. The sensor was removed by removing the two screws holding it in place in the upper left hand corner of the oven. I had to disconnect the sensor on the back of stove. Then I pulled the old sensor through the hole inside the oven. Then I installed the new sensor by putting the wire of the sensor through the hole where the old sensor was removed. Then I hooked up the wire in the back of the stove. Then took the screw driver and replaced the two screws holding the sensor in place. It was very easy to do and the oven is doing fine now.

Removed oven door (slides out). Removed side and bottom screws from frame and slid new glass into place. screwed in the 8(or so) screws.

First, I called Sears who wanted $440.00 to send a tech out to repair the stove. Second, I visited various web sites to find out what the problem was. I watched a brief video on Part Select which showed the repair of the stove. I then checked other parts stores on the web and selected Part Select based on price and video. Installation was very easy just as the video showed. Stove was repaired in less than 30 minutes.