JES9860CCS01 Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steve from Centralia, WA
- Parts Used:
- JEA7000ADBA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old element did not work
just plugged it into the unit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen D from Columbia, MD
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
time to replace the filter
lift out old filter, wash, put in new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Funston, GA
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven not heating to set temp. 100 degrees too cold
installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from DENVER, CO
- Parts Used:
- WPW10586440
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The cooling fan was making extremely loud noises when running
For the Ikea Range isg650ws01, the repair was very easy.
Step 1) Slide the range away from the wall slowly, verifying occasionally to not strain the gas or electric lines
Step 2) Unplug the range
Step 3) There are 2 phillips heads screws holding the rear panel in place. Remove the two screws and remove the panel.
Step 4) The cooling fan is held in place with 2 phillips head screws. Remove the screws and disconnect the electrical cord
Step 5) install the new cooling fan. The electrical plug can only be inserted one direction, so there shouldn't be a concern that you have the plug installed correctly. Match the original orientation of the fan in the unit. Re-install the 2 screws for the fan, and then install the rear cover. There are 2 slots that the panel needs to slide into in the bottom. Finish the install by installing the 2 screws you removed in to hold the rear panel. Plug the range back in and heat to 450°F to validate the repair.
Step 1) Slide the range away from the wall slowly, verifying occasionally to not strain the gas or electric lines
Step 2) Unplug the range
Step 3) There are 2 phillips heads screws holding the rear panel in place. Remove the two screws and remove the panel.
Step 4) The cooling fan is held in place with 2 phillips head screws. Remove the screws and disconnect the electrical cord
Step 5) install the new cooling fan. The electrical plug can only be inserted one direction, so there shouldn't be a concern that you have the plug installed correctly. Match the original orientation of the fan in the unit. Re-install the 2 screws for the fan, and then install the rear cover. There are 2 slots that the panel needs to slide into in the bottom. Finish the install by installing the 2 screws you removed in to hold the rear panel. Plug the range back in and heat to 450°F to validate the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Seattle, WA
- Parts Used:
- WPW10310274
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking element went out
Removed old element, and easily popped in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from BURBANK, CA
- Parts Used:
- WP7801P173-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original rack had melted plastic on it.
Removed the original rack. Checked dimensions, installed the new rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from BEND, OR
- Parts Used:
- WP71002111
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Grease filter needed replacing.
Removed old filter and replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from SOLON, IA
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Oven temperature fluctuates
Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Lewiston, ID
- Parts Used:
- 74003645
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Inner Glass Pane
I received my glass panel realy quick from Part Select. It was an eansy job to install the new pane.
It took less than an hour. Thanks for Your prompt service.
It took less than an hour. Thanks for Your prompt service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis Rodriguez from Granbury, TX
- Parts Used:
- 12001656
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
F5 fault code kept appearing
I installed the new oven sensor but the problem continued. So I ordered a new relay board and installed it. Still no luck. So I pulled the new board back out and started trouble shooting it using my electronic background. I discovered the new board was using a pin for L2 that had no exit on the backplane, so I removed it and installed it where I believed it should go. Reinstalled the power relay board and presto. My oven is working lie a champ. Louis
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra M from DISTRICT HTS, MD
- Parts Used:
- WP7801P173-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven Racks were old
Replace the racks. No special instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Freda from Elizabethtown, NC
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grease filter needed replacing
Remove old filter- put in new filter. EASY!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Savoy, IL
- Parts Used:
- JEA7000ADBA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no heating element
I think Part Select is great, but my story? I just plugged in a module.
It was so easy...well...a technical writer--one of those people who writes operation manuals--could have done it. But afterward, they wouldn't have been able to explain to anyone other than another tech writer how it was done.
It was so easy...well...a technical writer--one of those people who writes operation manuals--could have done it. But afterward, they wouldn't have been able to explain to anyone other than another tech writer how it was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tommy from FAYETTEVILLE, NC
- Parts Used:
- 12001656
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No problem installing the sensor
I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from ARVADA, CO
- Parts Used:
- JEA8120ADBA
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
One of the burners in one of the glass ceramic cooktops stopped working.
I first thought it was the switch. I ordered one and the wrong one was shipped to me FROM ANOTHER COMPANY. After more trouble shooting I discovered it was the cartridge that needed to be replaces. I ordered one and again, the wrong one was shipped to me. They told me I could not get the right part because they were not made anymore.
So, I shipped it back and got in touch with Part Select. They found the right part and shipped it to me in 2 days. Problem fixed with the EXACT right part. I ordered the first part more than two months prior to receiving the correct part from PartSelect. All I had to do was plug it in to the recepticle in the stove. No tools required.
So, I shipped it back and got in touch with Part Select. They found the right part and shipped it to me in 2 days. Problem fixed with the EXACT right part. I ordered the first part more than two months prior to receiving the correct part from PartSelect. All I had to do was plug it in to the recepticle in the stove. No tools required.
Was this instruction helpful to you?
Thank you for voting!