D156B Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Funston, GA
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven not heating to set temp. 100 degrees too cold
installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Freda from Elizabethtown, NC
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grease filter needed replacing
Remove old filter- put in new filter. EASY!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Baltimore, MD
- Parts Used:
- WPY04100019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
element broken
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
This same repair 2 years ago thru a Factory repair "professional" had cost $200. My cost $42.00!! Cost to replace the entire range...$1700.00.
This same repair 2 years ago thru a Factory repair "professional" had cost $200. My cost $42.00!! Cost to replace the entire range...$1700.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from Winchester, VA
- Parts Used:
- 12200039
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
fan/light switch was melted due to a hot pot placed on top.
removing the vent grid on top, by lifting off, then taking out the filter screen. removed the 2 screws on the back of the switchplate, then slide it back. made a drawing of the color wires and which way the switch faces... (it matters)
I took off the the old press-nuts by just breaking them with needle nose pliers. removed the old switch, fitted the new one (paying attention to where the little prongs and big prongs were on the old switch. used the nut-driver to press on the new nuts that came with the switch, and hooked back up the wires, and put it back.
I took off the the old press-nuts by just breaking them with needle nose pliers. removed the old switch, fitted the new one (paying attention to where the little prongs and big prongs were on the old switch. used the nut-driver to press on the new nuts that came with the switch, and hooked back up the wires, and put it back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from Sugar Hill, GA
- Parts Used:
- WPY04100019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element shorted and caught on fire.
We cut off the electricity to the stove before touching anything. We removed the 2 screws on the plate that is mounted to the inner wall of the oven. Then we pulled the element out 2-3 inches and disconnected the wires. We connected the wires on the new bake element and pushed it into place, inserted the screws and DONE!
The bigger part of the "repair" was the clean up of the fire extinguisher residue inside the oven due to the fire.
The bigger part of the "repair" was the clean up of the fire extinguisher residue inside the oven due to the fire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nina from Coalinga, CA
- Parts Used:
- 703900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing knobs after tenant moved out
I got online, found this site, very easily found the part. The pictures were a tremendous help to ensure accuracy. The parts were delivered within 3 days without special postage. Without a doubt, I will order from here again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tommy from FAYETTEVILLE, NC
- Parts Used:
- 12001656
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No problem installing the sensor
I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Frankfort, KY
- Parts Used:
- W11117769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Renters removed leveling legs from refrigerator. I don't know why!
I tilted the unit back enough to scew the new legs into the threaded holes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from CARMEL, IN
- Parts Used:
- WP71002111, 8009
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
replaced grease filter
took out old one and after straightening out the significant bends in the metal frame holding the screen, that were caused by shipping the screen in too flimsy of a container, I installed this into the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Marshall, MN
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
filter was deteriorated from 15 plus years of use
lifted the top center panel off removed old filter installed new easy peesy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from STAUNTON, VA
- Parts Used:
- WP71002111
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Grease filter clogged and in need of replacement
EXTREMELY simple - drop in. AND- the part cost less than half the price quoted by appliance vendor...2 years earlier !!! This site is a marvelous resource for parts one can install with minimal skill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rudy from GARIBALDI, OR
- Parts Used:
- WP71002111
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old one was plugged
Pulled out old one and slipped in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Arvada, CO
- Parts Used:
- 12001656
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven would not hold temperature, not turn on, and would shut off during use.
Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Philips head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby K. from Huntsville, TX
- Parts Used:
- Y704660
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Needed replacement oven rack.
Part was perfect fit. Good product, good value, great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Charlotte, NC
- Parts Used:
- W11120791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burner had one temp. hot
Changed out surface burner switch.Unscrewed two screws, changed plug onto new switch.Don't forget to turn off power!
Was this instruction helpful to you?
Thank you for voting!