D156B Jenn-Air Range - Instructions

removed blower housing secured to floor with two screws then removed flexible vent pipe from blower housing then removed blower removed blower wheel and motor put new motor and wheel on put back on stove thats it..

Shut off power to range. Removed 4 phillips screws under control panel. Tip bottom of control panel up and out to unhook it from the range top. Remove half of old lens piece from slot in bottom of plastic lamp fixture. Insert smaller end of new lens through front of control panel hole. Slide lamp fixture slot over the inside end of lens until it clicks into place. Replace control panel. That's it.

Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

Removed top plate, disconnected old switch... Had to go to hardware store to get different push washers - the ones supplied with the part were too small. connected switch... tested connections and replaced top plate.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Move stove out from wall. Unplug from power. Removed four screws from the left side of the back (the side the light socket is on. Reach in and unplug the two wires on the back of the bulb socket assembly. Inside the oven, remove the bulb cover and the two screws holding the socket assembly. Remove assembly. Install bulb in new assembly, reattach the assembly to the oven back, reinstall the bulb cover. On the back of the stove, replug the two wires and replace the screws on the stove's back cover. Replug the unit to power and move back into position.
Sounds harder than it is. The worst part is reaching inside the oven to get at those bits.

First thing
disconnect from electricity
Remove the back cover by unscrewing its fixing screws
Using philips screw driver, To remove the scocket assembly, pull the tow electric wires from the socket, using a fine plier.
Open the oven door and unlock the glass cover and remove it.
Remove the 2 screws fixjing the socket from inside the oven.
Now the socket is ready to be disassembled by just pushing the clips with tow fingers.
Replace the socket and do same steps in reverse way.
insert the lamp, and the glass cover, connect the electricity and you are done.

Just replaced old with new, it plugs in same as old.

Easy job. Anybody can do it. This replacement is accessed from inside the oven.

1. Remove the two Phillips sheet metal screws that attach the backing element plate to the back wall of the stove.
2. Carefully and slowly pull out the element as far as you can to expose the two Faston connectors and wire.
3. While holding the heating wire exiting the baking element with the needle nose pliers, carefully remove each female Faston connector.
4. Installation of the new heating element is the reverse of above. I highly recommend that you use the needle nose pliers to hold the heating wire behind the male (spade) Faston connector while installing the female connector. This will prevent bending of the heating wire.
5. I also recommend turning on the new baking element to a high temperature for about 10 minutes with the door partially open to get rid of the new heating element odor before you bake any food.

Removed two nut screws (accessed with oven door open) with nutdriver, panel dropped out. Transferred wiring one-by-one to new switch, removed old switch with allen wrench, installed new switch, replaced panel. Done! However, the problem is not corrected and all other possibilities have been explored with no solution in site. Ideas needed.

lift out old filter, wash, put in new filter.

Unscrew the two screws. Pull the element out a few inches. Unclip the wires by pulling them apart. When we did this the wires retracted back into the opening. It was difficult to reach them and pull them back out. Be sure to hold the wires or clip something on them to hold them out till you can attach the new element. Attach the new element wires and screw the plate back on.