SVE47500W Jenn-Air Range - Instructions

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

I only had to unscrew two screws to remove the existing element. Unfortunately, when I removed the element I found that the electrical wire connected to it had melted off, so the element is actually still good. I had to strip the wire back and put a new wire connector on. Once that was done I hooked the element back on and screwed it back together.

1. Remove four screws on metal panel between top and lower oven doors. Pull the panel forward. You may need to open the top door partially to ease removal of panel.
2. Reach behind panel and unplug wire connector from old switch.
3. With panel free, squeeze ears on old switch and push through opening to remove.
4. Insert new switch in to hole and push from front to seat the switch. BE CAREFUL NOT to mess with the ears--if you try to splay them out (to better seat the switch) the switch will come apart.
5. Hold the panel up to opening to connect the wire harness to the switch.
6. Realign the metal plate to holes for screws and insert screws. (You may have to twist and turn to get the panel lined up.)
Done!

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

After examining the burner unit I noticed that one of the male contact spades was burned and look deformed. After removing the spade I discovered that it had been originally manufactured incorrectly. I went on line to try and find the part. I found it at this site . I ordered 2 of the spades and replaced the deformed spade and another one that looked like it had gotten a little hot. She tried the unit and it worked perfectly. She had not used that burner unit for a very lengthy time. The investigation of the problem took a little time, but the repair went very fast. Moral is :" If a spade doesn't look right, it probably isn't", but either the individual spade or plug can be replaced. This site is now my "GO TO" place for parts.

Simply unscrewed two screws holding the old element and replaced it with the new one. Note, of course I had to disconnect the wires that plugged into the back. Really easy and quick, less than $50 total for an that would cost over $2200 today.

We followed the DIY stories of others (like this one):

Turned off the breaker to the stove and removed the 4 screws under the control panel. The trim strip and the end caps did not have to be removed. The control panel was lowered just enough to clear the upper edge and then tilted forward so the connectors could be disconnected. Two screws holding the display in place were removed and the new display swapped out. Reassembly was disassembly in reverse.
Had to be gentle about unplugging and plugging in the ribbon cable.
Very happy with PartSelect product, delivery and website help.

My son removed the switch panel and unpluged
the switch. Then he replaced it with the new
switch fasten back the panel and turned the
power back on and everythiing worked fine.

very easy, removed two screws, unplug the wires on the old element, replug the new element , replace the screws.

Unfotunely this was not the entire problem. Ended up purchasing a new stove.

Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.

Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Make sure you turn breaker off install both wires and screw the bracket into the back of the oven. You could use a phillips screw driver but with my ovens age seemed like it wanted to strip it out so I used a socket instead. Turn on the breaker and it works like new

I removed the screws that held the element in place. I then pulled the element out and disconnect the two wires. Connected the wires and place element in place and screws to hold in place.

Note: this is the second part that I acquired to fix the problem. Had I listened to my wife the first time the problem would have been solved the first time around because she made the correct diagnosis.