SVD48600WC Jenn-Air Range - Instructions

I removed the screws that held the element in place. I then pulled the element out and disconnect the two wires. Connected the wires and place element in place and screws to hold in place.

Note: this is the second part that I acquired to fix the problem. Had I listened to my wife the first time the problem would have been solved the first time around because she made the correct diagnosis.

Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

1. Remove four screws on metal panel between top and lower oven doors. Pull the panel forward. You may need to open the top door partially to ease removal of panel.
2. Reach behind panel and unplug wire connector from old switch.
3. With panel free, squeeze ears on old switch and push through opening to remove.
4. Insert new switch in to hole and push from front to seat the switch. BE CAREFUL NOT to mess with the ears--if you try to splay them out (to better seat the switch) the switch will come apart.
5. Hold the panel up to opening to connect the wire harness to the switch.
6. Realign the metal plate to holes for screws and insert screws. (You may have to twist and turn to get the panel lined up.)
Done!

took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

So very easy!!!! I'm a 70 year old grandmother with a small socket set - and that's all I needed! Removed one small screw, removed old burner, popped new burner in, replaced one screw, and back in business! Placed order, received it in 2 days, fixed burner. So much faster than calling a repairman!

Removed old burner, replaced with new one, works perfectly! Only one screw to take out and use with new piece.

I only had to unscrew two screws to remove the existing element. Unfortunately, when I removed the element I found that the electrical wire connected to it had melted off, so the element is actually still good. I had to strip the wire back and put a new wire connector on. Once that was done I hooked the element back on and screwed it back together.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

We simply removed the front knobs, the 8 screws underneath the front panel and dropped down the control panel. We removed two screws holding the assembly and removed the ribbon cable and the two other connectors. We put the new one in and reattached all the cables and reassembled and it worked great. Took 15 - 20 minutes.

Open the door and remove the top screws holding the hinge retainer plates. Remove the three screws holding the glass in place at the bottom, the three screws and two nuts holding the top cover. Remove the glass, then the two screws holding the hinge in place. Reverse order for reassembly. Easy fix, but don't do what I did. I went cheap and only replaced the side that was bad only to have the other side go bad a few weeks later. Change both at the same time.

My husband did the repair. He had difficulty removing the old element, probably because it had been in there for 20 years. Once he got the old element out, it took less than 30 minutes to install the new one.

Turn off the electrical breaker before starting! Open the oven door & remove the 4 silver hex head screws under the bottom of the control panel with a 1/4 " nut driver. Pull out on the bottom of panel. This will access the clock assembly. Unplug the ribbon cable by pushing in & up on the small clips on each end of the connector - this is a little tricky but not that difficult. Remove the two small connectors and remove the two clock assembly mounting screws. Reverse the procedure for installation. This corrected the problem with the broil element not working - apparently the electronic clock assembly was the problem there as well.

Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.