88369 Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Wayne from NEENAH, WI
- Parts Used:
- WPY700854
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Numbers on surface burner knobs were illegibel.
I also sprayed them 3-times with a clear coat before installing. The clear coat I purchased at WalMart once I noticed it claimed to be safe for plastic. Avoid a clear lacquer based product.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Royce from Garland, TX
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knobs were worn badly
Pulled off old knob, then pressed on the new one.
It was very easy, and the part was the correct one.
It was very easy, and the part was the correct one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Phillidelphia, PA
- Parts Used:
- 12001222
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken oven door handle
First remove front oven door panel screws, then attach with 2 screws new handle part from inside door panel, reattach outer screws and job complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christy from MOLALLA, OR
- Parts Used:
- WPY700854
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
All four knobs were stripped
We cleaned the rod on the stove and pushed the new knobs into place. This Jenn Air range was made in 1980. Nice to know Jenn Air is still making parts for their ranges. We also ordered new coil elements which fit perfectly size 6 inch and 8 inch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- beatrice from TUCSON, AZ
- Parts Used:
- WPY700854
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burner knobs were wearing out, metal rims were falling off.
Just slid off the old burner knobs, and pushed on the new ones. The most difficult part of the whole thing was just being sure that I ordered the correct knobs that used a D fitting. I ordered some a year ago that weren't the correct fitting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynne from Weatherford, OK
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my old knobs were so worn that I couldn't see the numbers
I had tried several other "universal" brands from the home improvement center but nothing worked with my Jen-Aire. I finally ordered from PartSelect and they fit perfectly! My range-top looks brand new and finding and ordering the correct parts was amazingly easy. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melanie from SALIDA, CO
- Parts Used:
- 715396K
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Replace burnt out indicator light
I feel that the design of the indicator light, with the base attached to the bottom of the lens, is ingenious in that it eliminates the need for fasteners in that confined space, However, the plastic used for the base needs to be more flexible. Part of the base broke off in trying to force the base over the bottom of the lens. Fortunately, there was enough left on the base that I could slip it over the bottom of the lens and complete the installation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ricka from HOUSTON, TX
- Parts Used:
- WP715269
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
No heat in vintage JennAir oven
The oven on the 40 year old JennAir range stopped heating. It took more time to locate the model number D120 and conduct part/price search than the time it took to install the correct oven bake element from PartSelect! We read all the comments posted by others. We did not remove oven door. The old element had only 2 screws instead of the 3 reported by many. We followed the sequence--Power off at box; unscrew old element; pull out about 3 inches; disconnect wiring; used telescoping mirror to assist; connect wiring to new element; position new element; install 2 new screws; turn on power; turn on oven -- SUCCESS -- heating better than before. Thank you PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from ROLLING MDWS, IL
- Parts Used:
- WP715269
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
There was a third screw that I was not awhere off it was alittle difficult to get the lock but on the back.
Had to use a little mirror to get it on not a big problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Chapel Hill, NC
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Rear burner always high, ignored temperature setting.
Turned off breaker for range. Removed 4 phillips screws on control panel, tipped it forward and rested it on top of partially open oven door. Removed knob and nut on old switch. Moved wires, one at a time from old to new switch. Put new switch in place, tightened nut and pushed on knob. Put control panel back in place and installed 4 screws... piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beth from BROOKLAND, AR
- Parts Used:
- WP715269
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
After the old element kicked the bucket with a final loud buzz, it was time for a new element
I turned the breaker to the appliance off in the breaker box. Took a mirror and a flashlight to figure out what type of tools I needed. Turned out all that was needed was a phillips screw driver and a pair of vicegrips as the front mounting screws were in pretty tight. Disconnected the element mounting plate, pulled the element forward just a few inches to where I could get to the wire connectors and unscrewed them. Connected the wires to the new element, pushed it back into place and refastened the front mounting plate. Turned the power back on to the oven at the breaker box and turned the oven on the check the element and it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edgar from Montgomery, IL
- Parts Used:
- WP715269
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
super old Jenn-Air range needed an element
Pulled out the old one-couldn't find it ANYWHERE that was a comparable match except for partselect. shut off breaker to oven-put in the new one-hard to reach in due to limited space and hard to see due to sticking your head in an oven.used a mirror/flashlight to see behind element to unscrew and screw it back in.Other than space restriction and light-pretty easy. Works great! Thanks for HAVING the part!! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert A from Farmington `, CT
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Stove Top
Ordered new cartridges
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willi from Old Saybrook, CT
- Parts Used:
- WP7112P004-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Thermostat bulb was hanging loose
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub
Was this instruction helpful to you?
Thank you for voting!