JGS8860BDP Jenn-Air Range - Instructions

Considered calling a repair facility, after reading your tips and what parts should fix what problem I decided to fix myself. Moved oven out,slide in gas range. Took off probe and tested with volt ohm meter, read 1090 ohms, should have been good. I could see oven igniter glow red, but I decided to replace both units, glad I did. Oven go's from 100' to 350' in 8 minutes now, for less than $85.00 have a fully functioning oven now. I'm sure the repair would have exceeded $300.00 or more being we live in a rural area. Thanks for the tips from your experts as well as you customers.

I didn't. I'll need to return these knobs as they won't work for this oven. While they fit and look nice, the marks are 90 degrees off from the stove markings.

From reading other reviews i thought I would have to dis-assemble the door but when I saw the new part I realized I would not have to, simply pop the beveled clips w/pocket knife and pop in the new seal clips. the ends tucked very nicely, an 80+ yr. old would have no trouble if they had their wits.

Put a new one in.

1. Turn power off and loosen and remove screws. Pull out sensor from mounting hole and expose wire connector. Remove old sensor. Select appropriate wire adaptor and reconnect the sensor. Carefully push connector through hole and secure with screws removed previously. Turn power back on and cycle oven to make sure oven operates properly. If you have an oven thermometer it can be used to compare set point of oven to thermometer to make sure readings are the same. All done! Happy wife can now bake cookies again and now I can go back to man cave for other projects!

Took the bottom out of oven then removed and replaced with the new part. VERY EASY! I'm a 70-year-old woman and do quite a few home repairs myself.

The entire "project" took me less than 3 minutes, and required no tools at all! First, the saleswoman over the phone pointed me to the correct product for my problem ($30 less than what I thought I needed), and it arrived at my home within 4 days. Then, it was just a matter of pulling off the old gasket, and snapping the new one in place! Simple!

It's a straight forward job, remove remove the old touch pad then install the new one.

replaced heat sensor

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

Unscrewed burner assembly and removed wire. Unable to remove electrode screw. Striped head of screw. Tried penetrating oil but no luck. Tried to drill and use easy out bit but ruined burner assembly and had to order new burner assembly. When assembly came it had electrode in place but website does not show electrode with assembly except on one burner. With mail and all it took about a week to fix 2 burners. Returned unused electrode for credit. Overall, cheaper then a service call by far.

Watch the video. Spot on instructions. Easy peasy.

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

Oven and broiler have two seperate igniters. Broiler worked but oven did not heat. Oven igniter located under metal pan at base of inside of oven. remove pan by lifting, and remove completely from oven. Igniter under this pan and held in place by two srews. Remove screws, unplug from cable, replug in ne igniter, replace two srcews and pan, and you're done! this part cost about $50 and I installed, last time Sear replaced =$300.

This should be a 5 min job. Lift off the burner cover, remove two screws to lift of the burner base and then remove a Phillips head screw that hold the burner igniter in place.

Unfortunately, the screw holding the burner igniter was rusted and it could not be loosened. WD-40 did not touch it. I used a stronger penetrant, "Blaster". Still it would not budge. Then I used a small Phillips head screwdriver and a hammer which I used as an impact driver. I twisted the screwdriver slightly to loosen and hit it was a hammer. Then I twisted the screwdriver slightly to tighten and again hit it with a hammer. After the penetrant and a couple of more tries, the rusted screw finally moved!!!

With no rust, this should be an easy 5 minute replacement. The burner now works great!!!