JDS9861AAP Jenn-Air Range - Instructions

I had the part overnighted since Thanksgiving was in two days and we needed to be able to use the oven. I saw a video on the website that instructed how to unplug the stove. Unscrew the baking element from the inside of back wall of oven. Gently pull out the part to where it is attached to wires. Simply pull apart the male part from female parts. Replace the old element with new element and attach it to the pulled out wires. Then gently push back wires inside the back wall of oven. Screw the attachment back in. We then plugged the oven back in. Turned on the oven to about 300 degrees. We put an oven temperature gauge inside and after a time the oven temperature was at 300 degrees and steady. It was fixed. Thanksgiving was on!

the hardest part of this repair was the wait for the element to arrive in the mail - which was in 4 business days - then took 5 to 10 minutes to get to circuit breaker box in garage. That was the longest part of the repair. My husband took the door off the oven after turning the circuit off in the garage. Followed directions from others who made the same repair and it was done in 2 minutes! Super easy - thanks for saving us money during this time of tight budgeting around the holidays! You're a lifesaver!

lift out old filter, wash, put in new filter.

I took the broiler pan out of the shipping container and put it in the oven.

after finding my part and thank god for you guys i recieved it early it only took 4 days to get here i unscrewed my old oven part and popped the new one in easier than making cookies and now i can bake til my hearts content thanks for being there for me
barbara krebs

Disassembled the oven door, removed broken glass, replaced with new glass and reassembled oven door. Took very little time. Online diagram on this site helped to keep everything in order and easily know what part was needed. Thanks!!!!

First I turned the power off to the oven using the breaker switch. Removed the old bake element by first unscrewing the 2 screws for each bracket holding each side of the old bake element and unplugging the two current connections.

Replugged and rescrewed above. Turned breaker on for oven. Tested by turning oven to back and watching new bake element heat up.

Remove Vent Cover, Remove Old Filter, Replace With New Filter, Replace Vent Cover, Repair Complete

UNPLUG THE POWER CORD! This particular model is a (slide-in) unit, it was wedged between to fixed cupboards/cabinets. Therefore, there are really no side panels to speak of, this made the repair slightly easier. I simply slid the unit out enough to unplug the power cord and access the right side of the unit. All one needs, at this point, is a Phillips head screw driver to remove a small metal panel installed just below the stove top panel (right side of range), its held with approx. 8 screws. There is one other panel that must be removed as well, (you may want to remove this panel first). It is an enameled-like panel approx. 5" wide x 36" long located at the front of the range (right side) running the length/height of the range (held with 2 screws). Get those 2 panels removed and you will see the spark module attached near center of range just under stove-top panel. Module is attached to a small metal bracket, module has 6 wires attached to it (2 feeding the module and 4 exiting the module to the burners). Bracket screws are nearly impossible to get at (you need a very stubby Phillips screw driver, if you can even get your hand in there). Anyway, I simply released the module from the bracket, then carefully bent the bracket back toward me; to provide work area for my hands. The bracket bends easily and really can't be broken. Now, at this point (using longer needle-nose pliers) detach the wires from the old module (remembering each wires location) or, as I did, hold the replacement module near the existing module and transfer the wires one at a time. Now, slap it all back together as you took it apart. Really simple job, total time is easily/generally under 30 minutes. It may be easier to access the module by removing all the burner components and raising the stove-top? Not sure? I chose not to do the repair that way. Hard part was locating where the manufacturer hid the module on the range. :- ) D.I.Y.ers Rock!!!

-Disconnected power from oven at the circuit breaker.
-Removed oven door and racks.
-Removed two screws holding element to the rear wall.
-Carefully pulled element away from rear wall, exposing wire leads.
-Carefully detached wire leads with male Sta-Kon connectors from element ends. (Taking care not to break or weaken the wires at the connector.)
-Disposed of old element and placed new element in same position.
-Re-attached leads by very carefully sliding male Sta-Kon connectors into the new element connectors, taking care not to push too hard and bend element wire.
-Gently re-inserted element ends into wall and re-attached element to wall with original screws.
-Reconnected power and tested new element. Element did not heat.
-Disconnected power and looked for collateral damage from original element failure.
-Removed oven from wall, removed rear panel and identified the high-temperature limit switch.
-Removed Sta-Kon leads and checked switch for electrical continuity. It had none, apparently the result of the high current from original element short.
-Obtained new hi-limit switch from Part Select
-Removed and replaced hi-limit switch, re-attached leads.
-Replaced rear panel and reinserted oven in wall.
-Reconnected power and tested new element. Element heated normally.
-Returned racks to oven, re-attached door and done.

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.

I Lifted the oven door from the hinges and removed all the screws to get to the broken glass pane, since the oven door is in layers I taped the screws close to where they belonged, so that I could screw everything together again in the right order..
The last time this happened to me(!!) I brought the door to a repair man and hadto pay 200 dollars , I saved 150 Dollars doing it myself!

Remove the 2 burner assembly by gently lifting the rear burner and pull towards the back of the stove and the entire 2 burner assembly will slide out. Turn assembly up side down, remove all the screw on the cover with a philip screwdriver and remove cover. Once opened, you will see the ignighter, remove the 2 screws holding it in place, remove and replace the ignighter and secure with two screws. Follow the 2 lead wires and remove and replace with the new wires, simply pull off old and push on new wires. Replace the cover and all the screws, slide it back onto the stove and you will have ignition! Simple install, takes about 20-30 minures. If both burners are out, this is probably the problem. If only 1 burner is out, you probably need to replace the stove burner spark.

Prepare a flat area with newspaper, a screwdriver, and a small bowl for the screws, and a small wire brush (if you want to clean as you go). I also recommend taking photos as you proceed, for reference.

ALSO, take close note of the orientation of the cook top base, one end has a lip that's allows for burner assembly removal.

Remove entire two burner assembly, place upside down on newspaper, remove seven Phillips screws, remove assembly bottom.

Remove small screws from gas tubes, pay close attention as you remove the gas tube from the bottom of the burner, to the orientation of the two washers (the washers have an edge).

Remove the burner tubes and washers.

Carefully remove the igniter connectors from igniter.

Remove the end of the assembly.

Grasp the burners, and turn to rotate the burner to a position where the "bumps" on the burner match up with the gaps in the burner cook base. Remove the burners.

The old burner base can be set to the side. At this time i cleaned the burners throughly with a small toothbrush size wire brush.

Assemble the burners to the new top base by aligning the bumps to the opening in the cook top base, turn slightly to keep burner in place. Insert the gas tubes, with the washers (be careful about the washer lip orientation) with the smaller screws, do not overtighten!

Attach the igniter connector to the igniters.

Align the burner/gas tubes with the assembly end. Carefully set the base into place, adjust the tubes as necessary to get the screws aligned with the holes. Install the screws, tighten hand tight.

Install entire assembly into cook top, check igniter and burner operation.

Glass cleaner is great for cleaning the new porcelain surface.