SCE30500W Jenn-Air Range - Instructions

Simply unscrewed two screws holding the old element and replaced it with the new one. Note, of course I had to disconnect the wires that plugged into the back. Really easy and quick, less than $50 total for an that would cost over $2200 today.

My son removed the switch panel and unpluged
the switch. Then he replaced it with the new
switch fasten back the panel and turned the
power back on and everythiing worked fine.

Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.

I removed the screws that held the element in place. I then pulled the element out and disconnect the two wires. Connected the wires and place element in place and screws to hold in place.

Note: this is the second part that I acquired to fix the problem. Had I listened to my wife the first time the problem would have been solved the first time around because she made the correct diagnosis.

very easy, removed two screws, unplug the wires on the old element, replug the new element , replace the screws.

Unfotunely this was not the entire problem. Ended up purchasing a new stove.

Trial and error and reading and rereading the instructions.The use of the jumper wire was not detailed enough. Caller a repair man.

Oven sensor replacement was easy. Thermistor was installed in less than 15 minutes. After installation STILL had "F3" error message. Harness was ok, "Clock" or ECU needed to be replaced. "Computer" is obsolete, no spares available, some companies will rebuilt for $400+. Since the stove was going to the landfill I had nothing to lose by taking the "Clock" apart. It has one chip that is probably the power supply and control chip, another chip is an EEPROM with 128 bytes of storage and the last is a darlington chip that controls the relays. Cleaned up everything that looked like it needed cleaning with alcohol. When I reassembled the unit the pins for the thermistor harness felt loose, so I took it apart, again, and found cold solder joints on all four pins. It must have been there all along but plugging and unplugging the harness finally broke out the solder so I could see it. Soldered the pins back in and now it all works. It's worth a try if you're getting the "F3" message. If the relays on your stove aren't working it would be a good idea to replace the darlington chip. Good luck.

The sensor is mounted in the top right side of the oven.An extra long screw driver helps to avoid damage to the sensor when replacing it.The connectors were the opposite to the old sensor and I did not see that there were adapter cables included. It might help to connect or tie these together as I only expected the sensor and did not look for adapters.I had cut the wires and used wire nuts when I found the adapters.The repairs works fine.
Mike

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

Open the door and remove the top screws holding the hinge retainer plates. Remove the three screws holding the glass in place at the bottom, the three screws and two nuts holding the top cover. Remove the glass, then the two screws holding the hinge in place. Reverse order for reassembly. Easy fix, but don't do what I did. I went cheap and only replaced the side that was bad only to have the other side go bad a few weeks later. Change both at the same time.

My husband did the repair. He had difficulty removing the old element, probably because it had been in there for 20 years. Once he got the old element out, it took less than 30 minutes to install the new one.

Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it easily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

IMPORTANT WIRE CONNECTIONS: The manufacturer instructions describing where each wire connects is woefully incomplete. There are 6 or 7 wires to connect and only 2 are explained in the instructions. I took several photos of the original switch showing where each of the wires was connected before disconnecting and installing the new switch. If I hadn't taken the photos I would have been completely lost on where each wire connected.

My cook top has the red wire piggybacked along all the cook top switches. It was easy enough to reroute the red wire coming from the dual surface burner to pin 4 i believe on the new switch. Follow the previous thread and look at the instruction sheet online for this switch