SCE30500W Jenn-Air Range - Instructions

The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.

I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.

Followed the first persons instructions and they worked perfectly including using the jumper wire.

Very easy. 1. Turn off power to oven. 2 move the adjustable grills out to gain better access. 3. There are two phillips head screws that hold a bracket to the back of the inside oven. Unscrew both screws. 4 pull the bake element out about 6". This exposes the two electrical connections. 5. Use a plier and wiggle the slide on connector off of the old bake element. 6. With your fingers, slip the old connectors onto the new bake element. 7. Slide the element and wires back in the insulated pocket. 8. Screw both screws back in. 9. Turn on power and make your wife back you chocolate chip cookies just to "test". Sit in an easy chair and enjoy your cookies. If this took longer than 30 minutes inclding baking the cookies, it took you too long. If the cookies are not good, replace the wife. May take a little loger though :)

I had an electrician do it. The instructions were horrible. He followed the instructions from your web site. The cooktop was not on an island so he could not remove all the screws to release the top so he worked with the top propped up. When he finally got the connections on, the small burner would not work only the large outer burner is working. He went on the computer to see if he could get more information but was unable to find any information.

unplugged oven. removed 2 screws that hold the sensor in place, then removed the dozen or so screws that hold on the rear panel, unplugged sensor and fed wire through insulation. identified and installed correct harness adapter then fed new wire and connecter through insulation and connected to adapter. installed sensor retaining screws.plugged oven back in and tested function.no dice. unplugged oven once again. removed oven control panel and upon inspection of printed circuit board discovered 3 solder joints had failed. dang. resoldered failed joints and also sweetened up a few others that looked suspect. reinstalled controller, replaced all retaining hardware, and plugged in the oven. tah-dah!! works like a charm now. moral of the story is check the pc board first and save $50 for unneeded pats!!! or buy the controller from parts direct for $260ish. btw a roll of solder and soldering iron from an auto parts store cost around $10, learned to solder on you-tube $0. amazing all the home appliances yo can fix if you're not afraid to take a few screws out and poke around a bit. CHEERS!

Raised the unit and blocked it with 2 boards. TURN OFF THE POWER IF YOU WANT TO COMPLETE THIS REPAIR. Removed the philip head screws for removal of glass top. Remove the corner screws on switch end. Remove screws holding the switch. Remove screws holing the bracket for all switches. Lift and roll gently to get at wiring. Follow the directions for moving wires from old switch to new switch. MOVING WIRES IS THE MOST IMPORTANT STEP. Reverse your procedure to put back together and when finished remember to turn on the power.

First I called a repairman and left a message. That was 3 weeks ago. So, I 'googled' the error message and determined what part I thought I needed. Ordered the part on Wednesday evening and it was there when I got home from work on Friday. I unpacked the part, got a phillips screwdriver and then watched the repair video on your website. About 20 minutes later I pushed my stove back in place and the flashing said 'set time'. Then I checked both ovens, and have since used both, and everything works!!

took out the old dome cover and replaced it with a new one by unscrewing and replaced the new one and a fiberglass gasket. simple.

1. Remove four screws on metal panel between top and lower oven doors. Pull the panel forward. You may need to open the top door partially to ease removal of panel.
2. Reach behind panel and unplug wire connector from old switch.
3. With panel free, squeeze ears on old switch and push through opening to remove.
4. Insert new switch in to hole and push from front to seat the switch. BE CAREFUL NOT to mess with the ears--if you try to splay them out (to better seat the switch) the switch will come apart.
5. Hold the panel up to opening to connect the wire harness to the switch.
6. Realign the metal plate to holes for screws and insert screws. (You may have to twist and turn to get the panel lined up.)
Done!

I only had to unscrew two screws to remove the existing element. Unfortunately, when I removed the element I found that the electrical wire connected to it had melted off, so the element is actually still good. I had to strip the wire back and put a new wire connector on. Once that was done I hooked the element back on and screwed it back together.

Removed glass top from stove by taking out hex screws which secured glass top to stove frame. There are two phillips head screws inside the exhaust as well. Removed two phillips head screws which hold the burner switch in place. With a sharpie pen I marked the color coded wires on the faulty switch. Removed wires from the faulty switch. Replaced new switch using the old switch as a guide to insure that wires were connected properly. Secured new switch and glass burner top reversing above procedure. Problem solved. Note: The white dot on the control knob did not line up properly with the off position. Black out white dot and make a new one in the proper spot on the knob.

Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Make sure you turn breaker off install both wires and screw the bracket into the back of the oven. You could use a phillips screw driver but with my ovens age seemed like it wanted to strip it out so I used a socket instead. Turn on the breaker and it works like new