S101 Jenn-Air Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Lansdale, PA
- Parts Used:
- WPY04100019
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The bottom baking element burned out
Easy job. Anybody can do it. This replacement is accessed from inside the oven.
1. Remove the two Phillips sheet metal screws that attach the backing element plate to the back wall of the stove.
2. Carefully and slowly pull out the element as far as you can to expose the two Faston connectors and wire.
3. While holding the heating wire exiting the baking element with the needle nose pliers, carefully remove each female Faston connector.
4. Installation of the new heating element is the reverse of above. I highly recommend that you use the needle nose pliers to hold the heating wire behind the male (spade) Faston connector while installing the female connector. This will prevent bending of the heating wire.
5. I also recommend turning on the new baking element to a high temperature for about 10 minutes with the door partially open to get rid of the new heating element odor before you bake any food.
1. Remove the two Phillips sheet metal screws that attach the backing element plate to the back wall of the stove.
2. Carefully and slowly pull out the element as far as you can to expose the two Faston connectors and wire.
3. While holding the heating wire exiting the baking element with the needle nose pliers, carefully remove each female Faston connector.
4. Installation of the new heating element is the reverse of above. I highly recommend that you use the needle nose pliers to hold the heating wire behind the male (spade) Faston connector while installing the female connector. This will prevent bending of the heating wire.
5. I also recommend turning on the new baking element to a high temperature for about 10 minutes with the door partially open to get rid of the new heating element odor before you bake any food.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grady E from Vidalia, GA
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed Replacement Filters
Remove Vent Cover, Remove Old Filter, Replace With New Filter, Replace Vent Cover, Repair Complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen D from Columbia, MD
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
time to replace the filter
lift out old filter, wash, put in new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Monmouth, OR
- Parts Used:
- WP74008014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken oven door hinge
I watched a You Tube video,removed and dismantled the door, installed the new hinge. I forgot to remove the small pin which is similar to a rivet. When I tried to close the door it bent. Eventually, I remembered the shipping pin and pulled it out with any damage. Believe it or not, I had read about the shipping pin on customer comments on PartsSelect...Good luck, it is relatively easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Baltimore, MD
- Parts Used:
- WPY04100019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
element broken
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
This same repair 2 years ago thru a Factory repair "professional" had cost $200. My cost $42.00!! Cost to replace the entire range...$1700.00.
This same repair 2 years ago thru a Factory repair "professional" had cost $200. My cost $42.00!! Cost to replace the entire range...$1700.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from Sugar Hill, GA
- Parts Used:
- WPY04100019
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element shorted and caught on fire.
We cut off the electricity to the stove before touching anything. We removed the 2 screws on the plate that is mounted to the inner wall of the oven. Then we pulled the element out 2-3 inches and disconnected the wires. We connected the wires on the new bake element and pushed it into place, inserted the screws and DONE!
The bigger part of the "repair" was the clean up of the fire extinguisher residue inside the oven due to the fire.
The bigger part of the "repair" was the clean up of the fire extinguisher residue inside the oven due to the fire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from CARMEL, IN
- Parts Used:
- WP71002111, 8009
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
replaced grease filter
took out old one and after straightening out the significant bends in the metal frame holding the screen, that were caused by shipping the screen in too flimsy of a container, I installed this into the range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Marshall, MN
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
filter was deteriorated from 15 plus years of use
lifted the top center panel off removed old filter installed new easy peesy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from STAUNTON, VA
- Parts Used:
- WP71002111
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Grease filter clogged and in need of replacement
EXTREMELY simple - drop in. AND- the part cost less than half the price quoted by appliance vendor...2 years earlier !!! This site is a marvelous resource for parts one can install with minimal skill.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rudy from GARIBALDI, OR
- Parts Used:
- WP71002111
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old one was plugged
Pulled out old one and slipped in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Freda from Elizabethtown, NC
- Parts Used:
- WP71002111
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grease filter needed replacing
Remove old filter- put in new filter. EASY!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Frankfort, KY
- Parts Used:
- W11117769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Renters removed leveling legs from refrigerator. I don't know why!
I tilted the unit back enough to scew the new legs into the threaded holes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANCIS from MILLBURY, MA
- Parts Used:
- W11120795
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Right front burner switch burnt out
Shut off power. Removed screws holding panel.Removed wires from old switch.Installed wires on new switch and reinstalled panel.EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Owen B Douglass from BROOMALL, PA
- Parts Used:
- W11120795
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burn was full on or "high" at any switch position other than off.
Followed other's instructions from the web site: First - turned off the power at circuit breaker; removed two screws from downdraft vent area; pushed the switch housing back towards vent and lifted; held replacement switch next to defective switch and removed and replaced one wire at a time; loosed switch collar-nut and swapped defective switch for new one. Only issue was the "rat's nest" of wires gave very little room to work, especially if you have average sized hands.
Was this instruction helpful to you?
Thank you for voting!
burner cartridge terminal broke due to electrical shock. circuit shortage caused the problem.
dissembled the burner, remove the broken blocpk and bad spade.rewiered and assembled the burner.
Was this instruction helpful to you?
Thank you for voting!