S136-C Jenn-Air Range - Instructions

Followed the instructions given by Paul from Mickleton, NJ. Very simple, no problem. Using two small blocks of wood to hold spring loaded hinges out while I replaced the door on the hinges was a big help. Thanks for the excellent delivery time. Great service.

Simple, take off the old and put on the new/ Delivery was excellent (next day).

Finding part needed and quick shipping were great. Web site so helpful. Initial attempt to remove old part was troublesome because I took out wrong screws thinking I had to remove parts beneath burner. Once I figured it out, it was so easy.
1. Turn off power.
2. Remove 4 screws BELOW control panel (open oven door to see them)
3. Pull off 7 front knobs.
4. Lift out loosened panel.
5. Take out the two screws holding control switch to front panel. Note orientaion of switch.
6. Replace wire by wire to new switch.
7. Put it all back together. Make sure switch is put in same direction.
8. Turn power on.

removed 4 screws holding entire face plate. Rolled face plate up on top of stove and left all wires attached (many). removed 4 screws adjacent to clock assy. Removed control knob just on either side of clock assy and removed control screws (2 on each). removed wires attached to clock assy and transferred new assy. Re-assembled and set clock time.

Changing the complete front control module would not have been a hard job but the two screws under the left stove knob would not release and the hex wrench stipped the bolt. I was able to undo both right screws on the right knob, releasing the knob control and the right bracket that holds the center control module. Being careful I pried the two left side tabes on the left bracket allowing me to slide the control module
out. I replaced the module and reversed my steps. The top switch that controls the downdraft and oven light was simple. Remove the two screws that holds the bracket housing the switch. Remove the two hold down compression nuts by prying them up. hold broken switch next to new one and attach the four wires. Replace switch, tried to replace the two compression nuts and after a half hour figure out they are too small. Spen another half hour in assorted nut drawer until I found two small nuts and luckily was able to force thread tham on. I can't believe I saved at least $200.00 in labor doing the repair myself. (and the stove works). I'll be doing my own repairs myself from now on. (Okay, within reason)

Removed the blower assy. Removed the motor. installed the new motor. Reassembled the blower assy. The problem I had was getting the proper clearance for the squirrel cage blower fan to rotate without rubbing on something. I had to make shims for the mounting flanges of the housing to get it to work. Took a lot of head scratching.

Since the motor is larger than the original, remove metal flange; shim one side of housing with 3 washers per screw and reseal..simple! Works great.

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

Much to my horror, what was described as a simple, 15-minute replacement, took 3 days! In order to replace the oven door gasket, I had to disassemble the entire door. Every photo I saw of the gasket showed it as a flexible part: gently pull out the old one and push in the new. What I received in my order had a frame. In order to replace it, I needed to unscrew the door parts. Unfortunately, I made a few rookie errors, primarily because I kept thinking the next screw would release the gasket frame. So I neglected to keep track of the screws I removed, and I didn’t take any photos!
I must have used half a roll of masking tape to keep parts together; I did not have 5 hands! When I released everything and nestled in the frame, I had even more trouble replacing all the screws I took out. The majority of holes did not line up. So I just did the best I could, put in as many screws as I could. But after three days of working, I finally finished. It all held together, and the door did what it was designed to do. Really a repair horror. And I am not an incompetent novice!

Motor (Blower Motor Kit) Part Number: PS1569907
No instructions are included in the package from PartSelect. Disassembly from the main housing was relatively simple. I found that paying VERY careful attention to how the original motor was wired and mounted would pay off in correct re-assembly, conquering motor vibration and rubbing. Most of my project time was spent cleaning the rotating blade wheel from 20 years of grease build-up. On tools, I would have appreciated the inclusion, or availability as an accessory, of a long-stem correct-size allen wrench (used in removal of the fan blade wheel.) The job went well, and probably saved me $200 in service call and labor.

First Inserted 2x4x 36" length of wood behind the spring loaded door hinges to ease removing the oven door as I worked alone (this was recommended in a previous post and was essential when working alone, TY). Removed 2 retaining screws on the interior side of the door at the hinge locations. Slid the door up an off the hinges, moved door to a cloth pad protected work bench. Took the door and glass panels apart removing all the related screws, retaining clips; taking note of screws, retaining clip and panel locations for reassembly. Removed the insulation, removed the glass window pack, and removed of all rust fragments (dust) between the 2 glass window panels. The glass window pack metal molding retainer, on the oven interior side of the glass window had completely rusted away. Removed the existing oven door gasket. Cleaned the glass door window pack, and interior side of the oven door surface. Installed the new gasket, which fit very well. Tightened the loose door handle screws. Reassembled in reverse order all door components noted above, and replaced the door onto the hinges, fastened the 2 door hinge screws, removed the 2x4x36" wedge holding the hinges in the open position, and closed the door. Job complete. Thanks to previously posted directions as a good guide. Hope this helps as well.

Fortunate to have the replacement parts available.
Wish a replacement door window pack was available, as the double glass, metal edge seal is deteriorating, and the metal molding retainer that held the glass in place is completely rusted away on the oven side of the existing window pack. Plan to find heat resistant caulk to seal the glass in the door, in lieu of the metal molding glass retainer.

removed 4 screws holding burner controls. removed wires off old and placed on new burner control. very pleased with quick shippig of part. two days and range was as good as new. excellent company to buy from

First we had to remove the screws holding the frame of the oven door together where the glass goes. We slipped the glass into the space inside the door frame, screwed on the handle, closed the frame and replaced the screws. It was simple, quick, and it looks great!!

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.