SVE87600W Jenn-Air Range - Instructions

Open oven door
Remove two sets of four screws underneath the LED display
Remove stove handles (pull off easily - no tools needed)
Lower flat plate width of oven and about two inches deep should be able to drop out from under the clock display.
Remove face plate over clock.
Unscrew four screws holding clock unit down.
Undo two electric connectors and the thin ribbon connector - the thin ribbon connector is different - the ribbon comes loose and the black plastic connector stays in place on the board.
Press the thin ribbon connector ends inward and pull up to detan ribbon on old one and then to insert ribbon on new one.
Reverse the rest.
Not too bad!

I first turned the power off to the stove at the junction box. Removed the control panel that contained the clock assembly by removing 4 phillips head screws. While my wife held the control panel, I disconnected the two pin connectors and one ribbon connector attached to the clock. I then removed the two phillips screws holding the clock assembly in place. To disconnect the ribbon connector, press the release buttons on the side in and the center loosens and pulls out, releasing the ribbon. There are two plastic tabs that fit into two guide holes on the ribbon. The best part of this is that 6 months ago, two number keys and the timer button had quit functioning and I thought I was going to have to replace the touch panel also. Apparently it was a problem with the circuit board on the clock assembly because everything works now! My ife is very happy!

Removed old filter and replaced with new.

As described by many others before. Turned off the power at the circuit breaker panel for the house. Unscrewed the front panel, disconnected the three connections to the old assembly and unscrewed the assembly.

Cleaned a few pieces then screwed in an connected the new assembly, put it all back together, turned on the power, said a prayer and IT WORKED!

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

Extremely simple repair to make. Move stove away from wall and disconnect power. Remove the oven racks. Remove the rear sheet metal panel covering the wiring harnesses. Caution: Sharp edges and corners on sheet metal.Sensor is located in upper left corner on rear oven wall. Using a long-shafted #2 Philips screwdriver, remove the two Philips head screws and gently pull the sensor 1" away from the oven wall. At this point, it will help to have an assist from someone while you are behind the range. Have the assistant gently tug on the sensor while you watch for wires moving on the rear of the range. After locating the sensor wires, gently disconnect the plastic connector clip. Note: plastic connectors become brittle with age and exposure to heat Move to front of range and gently remove sensor from rear wall by pulling the wiring through the oven wall. Before inserting the new sensor wire through the oven wall, "dry fit" the wiring connectors to see that the new sensor is a correct connection. Make connection, and secure the sensor to the rear oven wall with the two screws. Install racks, reinstall rear sheet metal panel, and connect the power. Set the oven baking temperature to a moderately low temp, 300 - 350 deg. to test the new sensor.

I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted

took out old one and after straightening out the significant bends in the metal frame holding the screen, that were caused by shipping the screen in too flimsy of a container, I installed this into the range.

I looked at the schematic from PartsSelect, undid the 8 screws and replaced the clock assembly. I probably saved $200 on labor doing it myself. I had the clock repaired in 30 minutes.

always remeber the first thing to do when working on electric components turn off the breaker
remove 2 screws securing the element, pull the element out enough to view the wire terminal attached to element and remove with needle nose plirers ,apply to new element ,replace screws

Once the display became too dim to read, I removed the front panel to determine how to access the piece and to check part numbers so that I could order the proper piece. Once the part arrived, being familiar with the disassembly, it was simple enough to replace the part quickly. The part came out with two screws and the connections were standard electronic multi plug, making the replacement simple. When we turned the power to the unit on, it worked first time.

Turned off the breaker. Removed the screws under the front panel and eight screws behind the burner controls (two each). I then slid out the panel and laid it flat on top of the stove. Removed the three connectors. Most difficult was the ribbon connector: Squeeze the clips at each end and slide the top half of the connector up. Then the ribbon slides out (practice on the new part). Only two screws held the assembly in. Reverse the process with the new assembly. Worked great!

Cut of electricity. Opened the oven door and removed some screw that were over the door that let a plate be removed. Then that let the part drop down that was holding the clock. I removed 2 screws that was holding the clock in place, unplugged the 3 connectors that feed the clock, attached the 2 screws back in that held the clock, put the part back up in place, added the plate and was done. Turned the power back on. I was delighted when I saw the clock light on. Easy to install.

This is the second clock I have had to put in this unit in about that many years. The first time I disassembled far to many things. This time I knew to only unscrew the front panel and side triangle plates. The process was much faster the second time. I hope this is not a chronic problem though.

I first turned off the circuit breaker for the range. I then I removed the four hex screws from the underside of the panel and then dropped the panel to expose the clock assembly. I then removed the two screws holding it in place, disconnected the cables and removed the old unit. I then reversed the procedure to install the new unit. I next turned on the circuit breaker restoring power to the range. And like magic I once again had light. I know I must have made by Daddy proud. I should have done it sooner. Thank you for making it so easy by sharing the "how to's" with me. It was especially helpful to have the model number.