FCE30510W Jenn-Air Range - Instructions

Took two screws out unplugged the element and plugged the new one in and replaced the screws and turned the breaker back on. Works great...Piece of cake..jk

First I cut the power to the stove. Then I unscrewed the two screws. Pulled the element out a few inches. I had to use pliers to disconnect it from its wires. It was a very tight fit. Then I reconnected the new element. Cut the power back and and fired her up. Boy did she burn like fire.

Watched the video that was available and followed the instructions. Unplugged the stove first,removed the old element, and put the new one in. Video was very helpful and the installation was very easy. Was done in about 10 minutes.

Removed 2 phillips screws, unplugged 2 wires, threw away old element. Installation of the new element was just as easy but in reverse order. Piece of cake!

I let my husband to the work...But it was very easy. I could have done it! He removed the screws, pulled the wires off previous element. Reattached the wires to the new element and screwed the ends back in place.

My husband has moved out of state for his job. I am left here with the children until the house sells. This is the first time I have ever had to do any oven repair. I had excellent and fast service - my part came right away. I took out the 2 screws holding the element in place, pulled the element out, disconnected the old element, connected the new one, pushed it back in, and replaced the screws. No problem at all. I was a little nervous turning it all back on, but it is working perfectly!

I first shut off the breaker to the stove - safety first!

I used a phillips screw driver to remove the two screws that held the old element in. Then I pulled the old element out and used the pliers to remove the electrical connections. I put the new element in, made the electrical connections and secured it with the screws. After restoring powere via the breaker, we tested the stove and it worked. Just call me the Maytag Man!

First throw the breaker on the stove. Remove two screws in back of oven then slowly pull out loosen the wire attachements ......got new part in 2 days just as simple reverse the removal directions.,,,I am over 60 female and it was simple.

Turned off power, removed 2 screws, un-hooked the connections, them put in the new element in reverse order.

First I turned off power to the range at the fuse box (very important-The last time I didn't do this and ended up paying a repairman $150.00 to replace the damaged connectors). I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the new element, pushed the element back in and replaced the screws. Turned the power back on and tested the element. The whole job took about 30 minutes because I had trouble disconnecting the old element. I used the flat end of the scrapper to push against the connector while I pulled the element out. Normally it would take only about 15 minutes.

Removed the old element by removing 2 screws and disconnecting two solderless connectors. One solderless connector was melted in two. I had to remove the rear panel and cut the old connector off and crimped on a new solderless connector. The time required was lengthened due to trip to the hardware store to get a new connector. While I was fixing the oven element my wife replaced the oven light.

Removed two screws from back of oven ,pulled apart old coil from wires, inserted new coil into the small metal pieces, pushed back and screws replaced. Really easy , anyone can do. Oh, I am 70 years old so probably people younger could do more quickly.

I followed peoples instructions here, and it was not very difficult.

First, the diagram on your website said remove two screws. The diagram looked like they were on the back of the stove on each side. On my stove there were three screws that were visible under the front lip upon opening the oven door. I removed the top, which comes completely off and set it aside. Be careful when removing the top. Don't drag it out, otherwise you'll tear up the asbestos around the other burners. Two people would be better for the inexperienced people. The new elements have been redesigned, so the diagram doesn't fit what you are looking at. Plus, the diagram on paper is looking underneath the element when you are looking down on the top of the element. I removed one wire and put it in the same spot on the new. Turned out it was not the element that was bad. It was a loose wire in the inside of the control panel.

Remove over door remove screws holding door togather remove old trim. install handle on new trim, install new trim to door reasemble door, reinstall door.