IJP87801 Inglis Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Art from Parma, OH
- Parts Used:
- 8053344
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Bad tempature sensor
Followed instruction on web site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Blackstone, MA
- Parts Used:
- WP9752294
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lower bake element failed
Removed the right side panel, lifted up insulation, removed element and replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENNIS from ROWLEY, MA
- Parts Used:
- W10823692
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The inner heating element was not working
The range top came off with two screws under the front portion of the glass top (by the oven door). I unplugged the connection plugs at the rear off the range top, unscrewed the rear screws holding the heating unit in place and plugged in new element and reassembled range unit. You need to removed the two phillip head screws at the rear of the range top in order to remove the bar holding the heating element. Once you do this it is very easy to finish the job.
Was this instruction helpful to you?
Thank you for voting!
broken interior glass in door
pulled door up and out. Disassembled door. removed old glass and rope gasket. installed new glass and gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Fort Wayne, IN
- Parts Used:
- WP9781593
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The inside oven glass cracked down the middle
I was able to remove the door by opening it partially and lifting it up while jiggling it. Once off, I laid it with the inside up on a table and the screws along the bottom facing outward so I could access them easily. I removed the various screws and porcelain covers and sides feel of easily. The inside panel lifted off exposing the inner glass and frame. The screws and clips had to be sprayed with penetrating oil to remove them. The frame lifted off and the cracked glass was removed. I was careful to wipe away all the fluid used to loosen the frame clips. Assembly was the reverse of this being careful to let pieces fit nicely without force. It would have cost me $39 to have the repair performed assuming I could get the door off. A Phillip's head screwdriver was not adequate to remove the frame clips. You needed a correctly-fitting square drive.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald L from Lancaster, CA
- Parts Used:
- WP3184533
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
27 year old Chambers Oven, Chambers out of business, Whirlpool helped
The oven light gasket had deteriorated with time and bulb changes. It is a self cleaning oven, which gets very hot during the cleaning cycle. The oven is old (27years) and off the "books" I selected a similar, but slightly smaller gasket (3" OD), and "fit" it to the 3.5" light fixture of the older oven. The gasket material was similar to the original, and I used a usable portion of the original,along with the new gasket to build a gasket for the light lense. Several years prior to this repair, I replaced the oven door springs. Whirlpool, who had taken over what was left of Chambers, had the springs. I did replace one heating element about 15 years ago. The Chamber's salesman told me that the Chambers was the "Cadillac" of all ovens, and it seems to keep running.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilma from Sanford, NC
- Parts Used:
- WP9781593
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
inner glass oven door shatterred
I was not around the entire time a neighbor was working to get the door removed. He only said he had to remove an additional screw so I'm not sure I can be of much help here.Once the door was removed however, the repair went easily. I would tell anyone needing this repair to be prepared to clean a number of crevices around the door. I was glad to have a chance to clean these hidden places.Let me also said customer service rep was wonderful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doyle from Oly, WA
- Parts Used:
- 8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The oven would bake for several minutes then turn its self off. It would not come back on until you reset it. The time varied from 10 to 15 minutes before turning off.
I took the back plate off of the oven by removing 3 screws and removed a single screw holding the sensor element in place, plugged the electrical 2 prong terminals back together and re-assembled the back of the oven. After the installation was completed we did a test run. It worked for aprox. 15 minutes and shut off again. It must have re-booted its self, cause when we tried it again it worked and still is working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Guy from McHenry, IL
- Parts Used:
- 8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Temperature Sensor Replacement
The Temperature Sensor was actually installed from the back of the oven. I had to remove about six(6) screws to remove a metal panel on the back of the stove. The connector the Temp sensor came with did not match the existing connector however it did come with wire nuts as an alternative. I cut the wires and connected them with the wire nuts and replaced the pannel. Very easy fix and my 13 year old oven still runs like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Sandusky, OH
- Parts Used:
- 814229
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Drawer Roller Snapped Off
Replaced both rollers....Quick and Easy!!
Was this instruction helpful to you?
Thank you for voting!
Oven Light bulb and gasket needed replaced
Removed the light cover - unscrew the bulb - place the gasket on the base of the light cover - replace the bulb - replace the light cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sarasota, FL
- Parts Used:
- WP8203546
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
circuit breaker blew
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from San Jose, NM
- Parts Used:
- WP3184533
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Gasket for oven light wore out and needed replacing.
I very simply replaced the gasket where it belonged and I was good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duane from Wildomar, CA
- Parts Used:
- 8053344
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven temp not hot enough
Followed Mfgs instructions.
Was this instruction helpful to you?
Thank you for voting!