RK962G1K3 Hotpoint Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Juan from North White Plains, NY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broken oven element
I removed the two screws that keep the element in place.Then I pull the element a little bit and disconnected the two wires and removed the old element. Then I reconnected the two wires on the new element then put the element back on position and put back the two screws that keep the element in place. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOE from WESTON, CT
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burned Out Lower Heating Element
Unscrewed the old one and screwed in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Marietta, GA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Baking Element not working
Repair was easy! I asked my son to take out the old and put in the new! He did! The oven works like new again for less than $50.00!!! Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dominick from Oceanside, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Coil element blew up breaking in three pieces.
I removed the plate held by 2 screws that holds the element, pulled the coil out and disconnected the yellow and red wires. Removed the broken one and connected the new one. Very simple. I also would like to add that you people are great to deal with and I will tell everyone to buy parts from PartSelect. Your service is outstanding and fast. Thank You.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Felicia from Little Rock, AR
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
The bottom heating element in the oven was not heating
First I shut off power to oven. Then I removed two screws from the back of the oven. Pulled elemeent out a couple of inches and diconnected from the power source. I removed the old unit and replaced it with the new one. Connected it to power source. Pushed element back into place and replaced the screws. Turn the power back on and turned on the oven. ....And there was HEAT!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Lewisville, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burned out.
I removed the two screws that hold the element in place; pulled the element out, disconnected the two wires held on by screws, replaced the element with a new one and reversed the procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Flower Mound, TX
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Beke Element broke into 3 pieces
followed the existing guidelines from this site.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Baldwin, NY
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burned heating element (no continuity)
Removed old part, install new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Meridian, MS
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
240 Volt Bake Element Failed In Upper Oven
Turned the main breaker off and locked it out. Removed the original element using a 1/4" nut driver. Installed the new element using a Philips screwdriver. Turned the power on. Tha'ts it. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Silver Spring, MD
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
My 20+ year old bake element cracked
I turned off the power at the breaker for the oven. I had to use a small wrench to get off the two screws keeping the bake element in the oven.
I pulled it out a bit and exposed where the element screws into the power.
To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.
After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.
Reset the breaker, and you're good to go.
Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.
I pulled it out a bit and exposed where the element screws into the power.
To prevent the wires from receding back into the wall after I unscrewed them, I taped them to the inside of the oven.
After removing the old element, I just installed the new one the same way. Screwed it into the power, and tightened the panel to the back of the oven.
Reset the breaker, and you're good to go.
Took 10 mins tops. It is pretty cramped in there and you need a good flashlight to see what you're doing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Mc Kinleyville, CA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
baking element failure
I was able to find the part here and replaced it the same day. You could use smaller boxes and packing, but thanks you for the part and help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Kennesaw, GA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
baking element burned out
Ordered the part and replaced the old one. Whole process took about 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackson from Arkansas City, KS
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bake Element burned and was not usable anymore
I read the instrustions provided and proceded to remove the old Bake Element and installed the new Bake Element.
It was no problem at all and was just a simple job to replace the bad part.
It was no problem at all and was just a simple job to replace the bad part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRIAN from WEST POINT, UT
- Parts Used:
- WB44X173
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
broil element had a "burn through", w/n turn on
less than 15 minutes R2 the part, ops ck'd good. 4ea 1/4" screw/nuts, they didn't fight me...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilfred from Freeland, WA
- Parts Used:
- WB44X200
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element burnt out
Element went out on Wednesday; ordered part on Thursday; it arrived on Saturday (via regular service). Took out old part with hex screw drived, installed new and back in business.
Was this instruction helpful to you?
Thank you for voting!