Models > RB636S1 > Instructions

RB636S1 Hotpoint Range - Instructions

Jump to:

All Instructions for the RB636S1
46 - 60 of 582
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Bernard from N CHARLESTON, SC
Parts Used:
WB17X5095
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
no burnt wire
Replace part an wires
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ervin from Milford, DE
Parts Used:
WB21X36771
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
infinite switch would not shut off at times.
First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.
6 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Fisher from Fort Collins, CO
Parts Used:
WB30M2, WB30M1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Surface Burners were very slow.
Removed old surface burners and replaced them by plugging in the new surface burners. Now they work GREAT! Parts ordered and received with-in 3 business days. Fed EX delivered parts in good order very quickly. We recommend PartSelect.com
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from SONORA, CA
Parts Used:
WB3X5699
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
missing knobs on clock and timers
Installed new knobs, mom is happy!!
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Placerville, CA
Parts Used:
WB31K10265, WB30M1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
not heating properly
Unplug coil, remove pan - place new pan, plug in new element and bingo. Took approximately 30 seconds!
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Shirley from ZEPHYRHILLS, FL
Parts Used:
WB2X7749
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
no problem liners for oven to protect oven from cleaning
apply liner on bottom liner of oven
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
wayne from GARLAND, TX
Parts Used:
WB44X173
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
broil element burn into
turn off electricity to stove and simply remove the screws from the heating element and put new element back in place .put screws in and turn power back on and test.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ann from WILMINGTON, MA
Parts Used:
WB31K10265, WB31K10266, WB30M2
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Needed new replacement surface element and drip pans
Surface element easily unplugged and removed, drip pans lifted out, New drip pans inserted, New 8" surface element and present 6" surface elements Inserted and plugged in.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
A K from LITHIA SPRINGS, GA
Parts Used:
WB44X5082
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Oven/ No Heat
Partselect made this job a breeze. Due to the user friendly process to order and receive the part. I repaired the stove after turning off the breaker in the main box. There were two screws that held the baking unit in place, removed them and then replaced with new unit.
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Lafayette, CO
Parts Used:
WB44X173
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Socket set
broiler element circuit broke
First removed oven door, according to Reader's Digest repair manual, then removed two screws holding element. Pulled element out several inches, then removed one side of bracket holding up front of element so that bad element could be pulled further out. Then disconnected two red wires from one side and two light blue wires from other side. Removed old Element. Attached two light blue wires to one side and two red wires to other pole, inserted element back into rear wall and attached with two screws, Re-attached bracket holding up front of element. Re-installed door. Tested and it worked fine.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
KATHY from SOUTH FULTON, TN
Parts Used:
WB2X8228
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set
wire burned on surface terminal block
I am a 62 y/o single female and was able to make this exchange of parts with ease. The toughest was getting the old terminal's wire clips free from years of gunk! I was pleased with the ease of installation and that it really worked afterwards. By the way, thank you Parts Select for getting this part to me very quickly. If a novice can diagnose, find the correct part and install it with success then anyone could do the same.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenny from CALDWELL, ID
Parts Used:
WB44X5082
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Bake element did not work
Got new part! Unplug range!!!
Remove oven door by opening and lifting up at the same time, set aside.
Remove two screws with a nutdriver or screwdriver.
Pull on element far enough to unhook wires and throw away old element and install the wires on the new element and reinstall!!
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Buffalo, NY
Parts Used:
WB31K10266
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
replace a drip pan
OK, I put the drip pan under the burner. Without a single problem.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Southern Pines, NC
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Surface element was corroded.
Removed existing surface element and replaced with new element.

P.S.

Part Select service was excellent.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Emma from The VIllags, FL
Parts Used:
WB30M1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
old unit failing to heat all coils
I first removed the unit by pulling gently from connection. Replaced the new one in that same manner - simply inserting into connection.

Very easy, I'll probably try it again soon.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the RB636S1
46 - 60 of 582